Bedienungsanleitung D-Link DI-304 (Seite 3 von 5) (Englisch)

728116

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

Ports 1x to 4x – These eight ports can be used to connect

end-stations to the router using straight-through cables.

ISDN – This socket is used to connect the ISDN line to

either an NT-1 or directly to the ISDN wall jack, depend-

ing on the type of service delivered by your phone

company.

Installation and Initial Configuration

Step 1 - Connecting an ISDN Line to

the Router

Your phone company will provide an S/T interface into

your home or office. Plug the ISDN line from the router

directly into the ISDN wall socket provided by your phone

company.

Step 2 - Connecting Ethernet Cables

to the Router

Your DI-304 has four ports for connecting 100BASE-TX

Fast Ethernet devices to form a LAN. The jacks for ports 1

through 4 are wired to let you connect network end nodes

(computers, servers, bridges, other routers, etc.) using stan-

dard “straight-through” EIA (Electronic Industries

Association) Category 5 or higher twisted-pair cables. The

jack for the sixth port is labeled Uplink and is wired to let

you connect to another 10Mbps or 10/100Mbps Ethernet or

hub or Switch using a straight-through cable, or an end

node using a cross-wired cable.

Please refer to the following chart when deciding on the

type of cable necessary for a given connection:

DEVICE PORT

USED

DEVICE

BEING

CONNECTED

PORT

TYPE

CABLE

TO USE

Hub or

Normal

Crossover

(X)

Normal

Switch

Uplink

Straight-

Through

(||)

Router Server (or PC)

Straight-

Through

(||)

Hub or

Normal

Straight-

Through

(||)

Uplink

Switch

Uplink

Crossover

(X)

Server (or PC)

Crossover

(X)

The figure below shows how to make an Ethernet connec-

tion between the router and a network end node.

RJ-45 connector

RJ-45 connecto

Important Notes on Ethernet Connec-

tions

Observe the following rules when connecting devices with

twisted-pair Ethernet cables:

♦ For both end-node and uplink connections, use only EIA

Category 5 or higher-grade twisted-pair data cables with

RJ-45 plugs. In almost all cases, only standard straight-

through cables are needed.

♦ Make sure no cable is more than 100 meters (328 feet)

long.

♦ When uplinking two hubs together with a straight-

through cable, use an uplink-type jack at one end, and an

end-node-type jack at the other.

♦ If uplinking more than two hubs together, observe the 5-

4-3 rule: no signal, in order to go from one end node to

another, must ever pass through more than five twisted-

pair cables, four repeaters (that is, hubs), and three up-

link cables. This is the maximum signal path in twisted-

pair Ethernet. Also be sure never to allow a signal loop

to form.

10BASE-T cable

(straight-through wires)

Note that you can connect an end node through the Up-

link jack, but to do so you must use a cross-wired cable

or cable converter.

Step 3 - Powering Up Devices for Ini-

tial Configuration

Plug in the included 18V AC, 1000 mA power adapter into

the power jack on the router’s rear panel.

You should have now connected the ISDN phone line, one

or more Ethernet cables, and the power adapter.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

D-Link DI-304 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von D-Link DI-304

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info