Bedienungsanleitung D-Link DWL-6620APS (Seite 61 von 136) (Englisch)

728147

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

Unied Access Point Administrator’s Guide

Page 61

October 2017

Section 4 - Managing the Access Point

Figure 30 - Congure WDS Bridges

Before you congure WDS on the AP, note the following guidelines:

•) When using WDS, be sure to congure WDS settings on both APs participating in the WDS link.

•) You can have only one WDS link between any pair of APs. That is, a remote MAC address may appear only

once on the WDS page for a particular AP.

•) Both APs participating in a WDS link must be on the same Radio channel and using the same IEEE 802.11

mode. (See “Modifying Radio Settings” on page 42 for information on conguring the Radio mode and

channel.)

•) When 802.11h is operational, setting up two WDS links can be difcult.

To congure WDS on this AP, describe each AP intended to receive handoffs and send information to this AP. For each

destination AP, congure the elds listed in the table below.

Field Description

Spanning Tree

Mode

Spanning Tree Protocol (STP) prevents switching loops. STP is recommended if you

congure WDS links.

Select Enabled to use STP

Select Disabled to turn off STP links (not recommended)

Radio For each WDS link on a two-radio AP, select Radio One or Radio Two. The rest of the

settings for the link apply to the radio selected in this eld. The read-only Local Address will

change depending on which Radio you select in this eld.

Local Address Indicates the MAC addresses for this AP.

For each WDS link on a two-radio AP, the Local Address reects the MAC address for the

internal interface on the selected radio (Radio One on wlan0 or Radio Two on wlan1).

Remote Address Specify the MAC address of the destination AP; that is, the AP on the other end of the WDS

link to which data will be sent or handed-off and from which data will be received.

Click the drop-down arrow to the right of the Remote Address eld to see a list of all the

available MAC Addresses and their associated SSIDs on the network. Select the appropriate

MAC address from the list.

Note: The SSID displayed in the drop-down list is simply to help you identify the correct

MAC Address for the destination AP. This SSID is a separate SSID to that which you set for

the WDS link. The two do not (and should not) be the same value or name.

Encryption You can use no encryption, WEP, or WPA (PSK) on the WDS link.

If you are unconcerned about security issues on the WDS link you may decide not to set

any type of encryption. Alternatively, if you have security concerns you can choose between

Static WEP and WPA (PSK). In WPA (PSK) mode, the AP uses WPA2-PSK with CCMP

(AES) encryption over the WDS link.

Table 30 - WDS Settings

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

D-Link DWL-6620APS Seite 61

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von D-Link DWL-6620APS

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info