Bedienungsanleitung D-Link DWL-6620APS (Seite 64 von 136) (Englisch)

728147

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

Unied Access Point Administrator’s Guide

Page 64

October 2017

Section 4 - Managing the Access Point

Field Description

Filter To set the MAC Address Filter, select one of the following options:

•) Allow only stations in the list. Any station that is not in the Stations List is denied

access to the network through the AP.

•) Block all stations in list. Only the stations that appear in the list are denied access to

the network through the AP. All other stations are permitted access.

Note: The lter you select is applied to the clients in the station list, regardless of whether

that station list is local or on the RADIUS server.

Stations List This is the local list of clients that are either permitted or denied access to the network

through the AP. To add a MAC Address to the local Stations List, enter its 48-bit MAC

address into the lower text boxes, then click Add.

To remove a MAC Address from the Stations List, select its 48-bit MAC address, then click

Remove.

The stations in the list will either be allowed or denied access based on how you set the lter

in the previous eld.

Note: If the MAC authentication type for the VAP is set to Local, the AP uses the Stations

List to permit or deny the clients access to the network. If the MAC authentication type is set

to RADIUS, the AP ignores the MAC addresses congured in this list and uses the list that is

stored on the RADIUS server. The MAC authentication type is set on the VAP conguration

page.

Table 33 - MAC Authentication

Note: After you congure local MAC Authentication settings, you must click Apply to apply the

changes and to save the settings. Changing some settings might cause the AP to stop and

restart system processes. If this happens, wireless clients will temporarily lose connectivity. We

recommend that you change AP settings when WLAN trafc is low.

Conguring MAC Authentication on the RADIUS Server

If you use RADIUS MAC authentication for MAC-based access control, you must congure a station list on the

RADIUS server. The station list contains client MAC address entries, and the format for the list is described in the

following table.

RADIUS Server Attribute Description Value

User-Name (1) MAC address of the client station. Valid Ethernet MAC Address.

User-Password (2) A xed global password used to

lookup a client MAC entry.

NOPASSWORD

Table 34 - RADIUS Server Attributes for MAC Authentication

Conguring Load Balancing

You can set network utilization thresholds on the UAP to maintain the speed and performance of the wireless network

as clients associate and disassociate with the AP. The load balancing settings apply to all supported radios.

To congure load balancing and set limits and behaviour to be triggered by a specied utilization rate of the access

point, click the Load Balancing tab and update the elds shown in the following gure.

Figure 32 - Modify Load Balancing Settings

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

D-Link DWL-6620APS Seite 64

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von D-Link DWL-6620APS

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info