Bedienungsanleitung D-Link DWL-6620APS (Seite 90 von 136) (Englisch)

728147

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

Unied Access Point Administrator’s Guide

Page 90

October 2017

Section 7 - Maintaining the Access Point

Packet File Capture

In Packet File Capture mode the AP stores captured packets in the RAM le system.

Upon activation, the packet capture proceeds until one of the following occurs:

•) The capture time reaches congured duration.

•) The capture le reaches its maximum size.

•) The administrator stops the capture.

During the capture, you can monitor the capture status, elapsed capture time, and the current capture le size. This

information can be updated, while the capture is in progress, by clicking Refresh.

Figure 60 - Packet File Capture

The following table describes the elds to congure the packet capture status.

Field Description

Capture Interface Select an AP Capture Interface name from the drop-down menu. AP capture interface

names are eligible for packet capture are:

•) brtrunk - Linux bridge interface in the AP

•) eth0 - 802.3 trafc on the Ethernet port.

•) wlan0 - VAP0 trafc on radio 1.

•) wlan1 - VAP0 trafc on radio 2.

•) radio1 - 802.11 trafc on radio 1.

•) radio2 - 802.11 trafc on radio 2.

•) wlan0vap1 to wlan0vap15. Trafc on the specied VAP on Radio 1.

•) wlan1vap1 to wlan1vap 15. Trafc on the specied VAP on Radio 2.

•) wlan0wds0 to wlan0wds3. Trafc on the specied WDS interface.

Capture Duration Specify the time duration in seconds for the capture (range 10 to 3600).

Max Capture File

Size

Specify the maximum allowed size for the capture le in KB (range 64 to 4096).

Table 53 - Packet File Capture

Remote Packet Capture

Remote Packet Capture allows you to specify a remote port as the destination for packet captures. This feature works

in conjunction with the Wireshark network analyzer tool for Windows. A packet capture server runs on the AP and

sends the captured packets via a TCP connection to the Wireshark tool.

A Windows PC running the Wireshark tool allows you to display, log, and analyze captured trafc.

When the remote capture mode is in use, the AP doesn’t store any captured data locally in its le system.

Your can trace up to ve interfaces on the AP at the same time. However, you must start a separate Wireshark session

for each interface. You can congure the IP port number used for connecting Wireshark to the AP. The default port

number is 2002. The system uses 5 consecutive port numbers starting with the congured port for the packet capture

sessions.

If a rewall is installed between the Wireshark PC and the AP, these ports must be allowed to pass through the

rewall. The rewall must also be congured to allow the Wireshark PC to initiate TCP connection to the AP.

To congure Wireshark to use the AP as the source for captured packets, you must specify the remote interface in the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

D-Link DWL-6620APS Seite 90

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von D-Link DWL-6620APS

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info