Bedienungsanleitung D-Link DWL-8710AP (Seite 20 von 136) (Englisch)

728146

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

Unied Access Point Administrator’s Guide

Page 20

October 2017

Section 2 - Getting Started

how to congure 802.1X by using the Web interface.

Using the CLI to Congure 802.1X Authentication Information

The following table shows the commands used to congure the 802.1X supplicant information using the CLI.

Action Command

View 802.1X supplicant settings

get dot1x-supplicant

Enable 802.1X supplicant

set dot1x-supplicant status up

Disable 802.1X supplicant

set dot1x-supplicant status down

Set the 802.1X user name

set dot1x-supplicant user <name>

Set the 802.1X password

set dot1x-supplicant password <password>

Table 6 - CLI Commands for the 802.1X Supplicant

In the following example, the administrator enables the 802.1X supplicant and sets the user name to wlanAP and the

password to test1234.

DLINK-WLAN-AP# set dot1x-supplicant status up

DLINK-WLAN-AP# set dot1x-supplicant user wlanAP

DLINK-WLAN-AP# set dot1x-supplicant password test1234

DLINK-WLAN-AP# get dot1x-supplicant

Property Value

--------------------------

status up

user wlanAP

eap-method md5

debug off

cert-present no

cert-exp-date Not Present

DLINK-WLAN-AP#

Verifying the Installation

Make sure the access point is connected to the LAN and associate some wireless clients with the network. Once you

have tested the basics of your wireless network, you can enable more security and ne-tune the AP by modifying

advanced conguration features.

1.) Connect the access point to the LAN.

•) If you congured the access point and administrator PC by connecting both into a network hub, then your

access point is already connected to the LAN. The next step is to test some wireless clients.

•) If you congured the access point by using a direct cable connection from your computer to the access point,

do the following procedures:

•) Disconnect the cable from the computer and the access point.

•) Connect an Ethernet cable from the access point to the LAN.

•) Connect your computer to the LAN by using an Ethernet cable or a wireless card.

2.) Test LAN connectivity with wireless clients.

Test the UAP by trying to detect it and associate with it from some wireless client devices. For information about

requirements for these clients, see “Wireless Client Requirements” on page 12.

3.) Secure and congure the access point by using advanced features.

Once the wireless network is up and you can connect to the AP with some wireless clients, you can add in layers

of security, create multiple virtual access points (VAPs), and congure performance settings.

Note: The WLAN AP is not designed for multiple, simultaneous conguration changes. If more

than one administrator is logged onto the Administration Web pages and making changes to the

conguration, there is no guarantee that all conguration changes specied by multiple users will

be applied.

By default, no security is in place on the access point, so any wireless client can associate with it and access

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

D-Link DWL-8710AP Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info