Bedienungsanleitung D-Link DWL-8710AP (Seite 24 von 136) (Englisch)

728146

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

Unied Access Point Administrator’s Guide

Page 24

October 2017

Section 3 - Viewing Access Point Status

Field Description

Persistence Choose Enabled to save system logs to non-volatile memory so that the logs are not erased

when the AP reboots. Choose Disabled to save system logs to volatile memory. Logs in

volatile memory are deleted when the system reboots.

Severity Specify the severity level of the log messages to write to non-volatile memory. For example,

if you specify 2, critical, alert, and emergency logs are written to non-volatile memory. Error

messages with a severity level of 3 – 7 are written to volatile memory.

•) 0 — emergency

•) 1 — alert

•) 2 — critical

•) 3 — error

•) 4 — warning

•) 5 — notice

•) 6 — info

•) 7 — debug

Depth You can store up to 128 messages in non-volatile memory and 512 messages in volatile

memory. Once the number you congure in this eld is reached, the oldest log event is

overwritten by the new log event.

Table 7 - Logging Options

Note: To apply your changes, click Apply. Changing some settings might cause the AP to stop

and restart system processes. If this happens, wireless clients will temporarily lose connectivity.

We recommend that you change AP settings when WLAN trafc is low.

Conguring the Log Relay Host for Kernel Messages

The Kernel Log is a comprehensive list of system events (shown in the System Log) and kernel messages such as

error conditions, like dropping frames.

You cannot view kernel log messages directly from the Administration Web UI for an AP. You must rst set up a remote

server running a syslog process and acting as a syslog log relay host on your network. Then, you can congure the

UAP to send syslog messages to the remote server.

Remote log server collection for AP syslog messages provides the following features:

•) Allows aggregation of syslog messages from multiple APs

•) Stores a longer history of messages than kept on a single AP

•) Triggers scripted management operations and alerts

To use Kernel Log relaying, you must congure a remote server to receive the syslog messages. The procedure to

congure a remote log host depends on the type of system you use as the remote host.

Note: The syslog process will default to use port 514. We recommend keeping this default port.

However, if you choose to recongure the log port, make sure that the port number you assign to

syslog is not being used by another process.

Enabling or Disabling the Log Relay Host on the Events Page

To enable and congure Log Relaying on the Events page, set the Log Relay options as described in the following

table, and then click Update.

Field Description

Relay Log Select Enabled to allow the UAP to send log messages to a remote host. Select Disabled

to keep all log messages on the local system.

Relay Host Specify the IP Address or DNS name of the remote log server.

Relay Port Specify the Port number for the syslog process on the Relay Host.

The default port is 514.

Table 8 - Log Relay Host

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

D-Link DWL-8710AP Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info