Bedienungsanleitung Dali IKON MK2 (Seite 8 von 38) (Deutsch, Englisch, Dänisch)

562740

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

3.5 DALI IKON ON-WALL

DALI IKON ON-WALL is designed exclusively for wall-mounting. The front bafﬂe is tilted for optimal

angling relative to the listening position. Therefore this speaker can be positioned in four different

ways: Mounted as front, rear, or side speaker to the left or right of the listening position it will be

slightly pointed towards your listening position; mounted as a centre speaker below the TV screen

it will point slightly upwards, and mounted as a centre speaker above the TV screen it will point

slightly downwards (see ﬁgure 6). Because the loudspeaker can be positioned in four different

ways, there are four brackets on the rear panel (see ﬁgure 7). Only one of these brackets should

be used.

On the rear panel of DALI IKON ON-WALL, there are four indentations to make room for the

loudspeaker cable between the speaker and the wall. This allows you to run the cable along either

side up or down depending on what works best for you.

3.6 DALI IKON SUB

For positioning the IKON SUB, please refer to chapter 9.1.

4.0 CONNECTION

Correct, tight connections to your ampliﬁer are extremely important for your listening experience.

Always use cables of the same type and length for left and right channels. We recommend using

special speaker cables from DALI, available from your dealer.

Connection in correct phase is a detail that is often ignored. The red (+) terminal of the ampliﬁer

must be connected to the red (+) terminal of the loudspeaker. The black (-) terminal of the

ampliﬁer must be connected to the black (-) terminal of the loudspeaker (see ﬁgure 9A). Even a

single loudspeaker connected out-of-phase in a stereo or surround installation will make the bass

weaker and the stereo image unfocused.

For the optimal listening experience, the right loudspeaker (as seen from the listening position)

must be connected to the ampliﬁer output terminals marked “R” or “Right”. The left loudspeaker

must be connected to the ampliﬁer output terminals marked “L” or “Left”.

NOTE: Before connecting cables or changing any connections, ALWAYS turn off your ampliﬁer.

NOTE: Make sure that the bare conductors are tightly gripped by the terminals with no loose wires

which, could cause a short circuit and damage the ampliﬁer (see ﬁgure 8).

NOTE: If you are using DALI IKON in a surround system, follow the instructions included with your

surround ampliﬁer.

4.1 SINGLE-WIRING vs. BI-WIRING/BI-AMPING

All DALI IKON speakers can be connected by means of a single speaker cable (see ﬁgure 9A + 9B).

However, DALI IKON 2, 5, 6 and 7 are ﬁtted with two pairs of terminals, allowing you the option

of running two sets of cables to each speaker. The top terminal pair is internally connected to the

crossover network’s high frequency section. The bottom terminal pair is internally connected to

the crossover network’s bass section.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dali IKON MK2 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dali IKON MK2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info