Bedienungsanleitung Dali PHANTOM H Series (Seite 8 von 37) (Deutsch, Englisch, Dänisch, Französisch)

745220

Zoom out

Zoom in

Vorherige Seite

1/37

Nächste Seite

UK DE DK CN FR

Every room has its own distinctive acoustics, which inﬂuence the way we experience sound from

a speaker. The sound you hear consists of both direct sound from the speakers and reﬂected

sound from the ﬂoor, and walls. The latter will affect how you experience the sound. As a basic

rule, try to avoid large, hard and reﬂective areas in the immediate vicinity of your loudspeakers as

it will typically cause strong reﬂections, which might disturb the precision and spatial effect of the

sound reproduction. Soft items such as carpets, curtains etc. might help if the sound is too bright.

Both the amount and quality of the deep bass depend on the size and shape of the room, and the

position of the speakers. Positioning the speakers near a side or back wall will accentuate the

bass. A corner location will accentuate it even more, but will also increase the reﬂections.

NOTE: The ﬂow damping foam material mounted on the back of the DALI PHANTOM H Series

should not be removed. It will assist in managing bass/midrange reproduction by damping

resonances in the cavity behind the open-back woofer.

4.1 Mounting the dogleg brackets

DALI PHANTOM H Series incorporates dogleg brackets for wall mounting. The brackets attach the

loudspeaker ﬁrmly to the rear of the surface on which it is mounted. The dogleg brackets extend

out at a 90-degree angle when the screws are tightened (see ﬁgure 3). The screws should be

tightened so that the loudspeaker sits securely in place – but be careful not to over tighten the

screws. To tighten the screws, use the 3mm Allen key (enclosed in the package).

If using an Allen bit it should be used with a hand bit screwdriver or a drilling machine with build-in

torque setting. If using a drilling machine, set the torque to the minimum setting. The screws are

appropriately tightened, when the gasket on the rear of the speaker is compressed and the bezel

of the speaker is ﬂush with the mounting surface.

If you need to remove the loudspeaker, loosen the screws approximately 5 to 20 turns counter

clockwise and the brackets will loosen their grip.

NOTE: Do not unscrew more than 20 to 25 turns or the brackets may fall off the screws.

If you are mounting the loudspeaker in very thick wall material, it might be needed to dismount the

dogleg brackets from the screws and afterwards mounting them upside down. Opposite mounting

of the doglegs will make it possible to mount the loudspeaker in boards with up to 2.75”/70 mm

thickness (see ﬁgure 4).

4.2 Grille

The metal grille is attached by means of magnets incorporated in the top of the speaker. Carefully

place the grille so that it covers the top of the speaker, and the magnets will secure it.

NOTE: On the inside of the grille there is a piece of non-woven. The non-woven is on the grille

to protect the drivers against dust and dirt. Therefore the non-woven must remain on the grille.

The supplied DALI logo badge can optionally be mounted on the grille. To mount the logo badge,

remove the protective ﬁlm from the rear side of the logo badge and position the logo on the grille

in the desired position (see ﬁgure 5).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dali PHANTOM H Series Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info