Bedienungsanleitung Dali SUB K-14F (Seite 9 von 91) (Deutsch, Englisch, Dänisch, Französisch)

745214

Zoom out

Zoom in

Vorherige Seite

1/91

Nächste Seite

UK DE DK FR CH

The connections are basically the same as stated in previous chapters, but for stereo setup

you should only connect the left channel output connector of your stereo or surround (pre-)

amplier/receiver to the LINE INPUT L connector on the DALI SUB K-14 F placed to the left

in your room. In a similar way you should connect the right channel output connector of your

stereo or surround (pre-) amplier/receiver to the LINE INPUT R connector on the DALI SUB K-14

F placed to the right in your room.

For a surround setup, split the output signal from your surround sound (pre-) amplier/receiver

using a RCA splitter (sold separately) and connect the two outputs. In all other respects, follow

the instructions above - but use separate channels. Please consult your authorised DALI dealer

if you have further questions.

5.0 INStALLING AND ADJUStING

Start by checking that the voltage of your mains output corresponds to the indication on the

back of your DALI SUB K-14 F. (see Figure 2)

WARNING: If the wrong voltage is supplied, there is a serious risk that the electronics of

the subwoofer will suffer permanent damage.

After checking the VOLTAGE, connect the mains cable and move the POWER switch to ‘ON’. The

subwoofer is adjusted using the controls on the rear side of the subwoofer (see chapter “10.0

Amplier Back Plate”) in accordance with the following tuning method which will help you

achieve the best results: Play a piece of music you know well, preferably one including rhythmic

bass such as kettle drums, bass guitar etc.

Since the performance is highly dependent on the main speakers, the listening room, the

subwoofer position in the room and your personal preferences, we recommend experimenting

with different settings to achieve the best listening results rather than giving any speciﬁc advice

on settings.

NOTE: The position of the subwoofer will signiﬁcantly affect its contribution to the overall sound

(see chapter “3.0 Positioning”). When you have decided which method of connection you want

to use and you have positioned the subwoofer, you can begin the process of tuning the system.

You are now ready to adjust your DALI SUB K-14 F.

5.1 PHASE SETTING

The PHASE switch of the subwoofer has two settings: 0° or 180°. The phase setting will adjust

the timing between the subwoofer and the main speakers. To set the phase, do the following:

1) Turn up the volume of your subwoofer a little higher than you would normally do.

2) Set the crossover point to maximum (120 Hz).

• NOTE: If you have connected the subwoofer via LFE instead of LINE IN you need to set the

crossover point for your subwoofer to maximum in the menu of your surround sound (pre-)

amplier/receiver.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dali SUB K-14F Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info