Bedienungsanleitung Danfoss 106 (Seite 1 von 2) (Englisch)

654602

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

GP Programmers & Timeswitches

102, 103 and 106 Models, for time control of Domestic Central

Heating Systems.

Wallplate/

Terminal Block

Plug-in Module

INSTALLATION AND WIRING INSTRUCTIONS

SPECIFICATIONS

Power Supply : 220/240Vac, 50/Hz

Switch Action : 1 x SPST, Type 1B

Switch Rating : 220/240Vac, 50/60Hz, 6(2)A.

Timing Accuracy : ± 1 min./month

Enclosure Rating : IP20

Pollution Situation : Degree 2

Max. Ambient Temp. : 55°C

Designed to meet BS EN60730-2-7

Dimensions : 112mm wide, 135mm high, 69mm deep

Rated Impulse voltage : 2.5kV

Ball Pressure Test : 75°C

The unit must be installed by a competent electrician and the installation

should conform to I.E.E. Regulations. This unit should be wired via full

disconnect in accordance with BS EN60730-1, e.g. via a plug and unswitched

socket or double pole switch outlet with neon.

INSTALLATION INSTRUCTIONS

1. Loosen the ﬁ xing screw in the base of the unit to release the grey

plastic Wiring Cover. Ensure the protective tape over the thumbwheel

remains in place.

2. Holding the unit clockface downwards, press ﬁ rmly in the centre of

the wallplate and slide it from the module as shown.

3. Fix the Wallplate/Terminal Block to the wall with countersunk No.8

woodscrews or to a steel box to BS 4662. 1970 or a surface mounting

steel or moulded box having centres of 2

" (60.3mm).

4. Referring to the Wiring Diagrams overleaf, connect the unit as shown.

Ensure that terminals 3 and 6 are linked where required (Mains

Voltage applications) with insulated cable capable of carrying full load

current.

5. Ensure all dust and debris have been cleared away from the area, then

plug the module ﬁ rmly into the wallplate ensuring that the hook at

the top of the wallplate engages with the slot at the back of the body.

Press the module down until it locates solidly.

6. Cut a cable aperture in the Wiring Cover if necessary; replace the Wiring

Cover, and tighten the ﬁ xing screw.

7. Switch on Mains and test for correct operation as follows:

i) Remove protective tape from the pre-selector wheel.

ii) Remove the dial cover and rotate the clock dial two complete

revolutions to clear the mechanism.

ii) Check that all positions of the Selector Switch and Tappets operate

correctly. (See instructions in User Booklet.)

8. Replace the dial cover. Finally leave the USER INSTRUCTIONS with the

Householder.

9. If the unit is to be left turned oﬀ and is in a dusty atmosphere, protect

the pre-selector wheel by re-aﬃ xing the protective tape.

IMPORTANT: Remove tape prior to putting unit into service.

Plug-in Replacement

Module

Selector Switch

Wallplate/Terminal Block

Pre-Selector Wheel

This product complies with the following EC Directives:

Electro-Magnetic Compatibility Directive.

(EMC) (2004/108/EC)

Low Voltage Directive.

(LVD) (2006/95/EC)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Danfoss 106 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info