Bedienungsanleitung Danfoss TP75-RF (Seite 3 von 4) (Englisch)

37611

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

18. These models are supplied with a factory pre-set programme which will

be active after a RESET has been performed. The pre-s e t

programme is shown in the chart with the Setting Instructions.

The chart also has spaces for users own times and temperatures a s

required by them.

19. The time and programme memory are maintained by the batteries

which should last more than two years. Every 24 months the batteries

should be renewed. Internal circuitry retains the time and programme

memory for one minute, long enough for the batteries to be changed.

If the batteries volts drop, before a change is due, a battery symbol will

blink in the display. When this occurs the TP75-RF will operate

normally for 2 weeks. After the 15th midnight all relays will switch to

OFF, the unit will shut down with just the time shown. When new

batteries are fitted the unit will start to operate normally again.

Advise the User to enter their own times and temperatures in the chart on the

Setting Instructions.

Post-commissioning

Optimum Start Control

If this has been enabled, initially set to the recommended 30 minutes start-

up duration and the event 1 temperature is not achieved by the event 1 time,

then refer to the Setting Instructions and increase the start-up duration one

stage, i.e. to 1 hour.

If the space temperature at the beginning of an Optimum Start sequence is

consistently lower than the programmed event 1 temperature by more that

2°F, then the event 1 temperature may not be achieved by the event 1 time.

In this case the event 1 time should be brought forward sufficiently to

compensate, so that the comfort temperature is achieved when actually

required.

Intelligent Anticipator

If, when the heating equipment is switched on, the room temperature is 4°F

or more lower than the programmed temperature the electronic anticipation

function measures the rate of rise in the sensed temperature and will switch

the heating plant off before the programmed temperature is reached. The

residual heat in the system after the heating plant has shut down will ensure

that the comfort temperature is achieved. This will improve the comfort

conditions and minimise fuel consumption.

Commissioning

12. Lower the front flap and remove the anti-discharge paper strip from

between the batteries and their contacts, and ensure the mains power

to the control circuit is switched on.

13. Press and release the recessed RESET button to ensure the factory

pre-set programme is active.

14. Once the programming has been completed, communication between

the thermostat and the receiver module has to be established.

a) SINGLE ZONE SYSTEM WITH RX1 RECEIVER

1 - Press and hold the LEARN button of the TP75-RF for at least 3

seconds. The thermostat will now transmit a continuous signal which

contains its unique identity for a period of 5 minutes.

2 - Within the 5 minute period go to the RX1 receiver module and

press both "PROG" and "CH1" buttons together and hold for at

least 3 seconds, then release.

During this process the RX1 receiver will have learnt the unique

transmission code of the thermostat and will in future react to all

transmissions from that thermostat.

To stop the continuous transmission on the TP75-RF unit press the

s button.

b) TWO ZONE SYSTEM WITH RX2 RECEIVER

1 - Repeat as above for zone one (CH1).

2 - Repeat steps one and two above for zone two, remembering to

press "PROG" and "CH2" on the RX2 receiver.

c) THREE ZONE SYSTEM WITH RX3 RECEIVER

1 - Repeat as above for zones 1 and 2 (CH1 and CH2).

2 - Repeat as above for zone 3, remembering to press "PROG" and "CH3"

on the RX3 receiver.

15. Establish with the customer the requirements for the operating

mode, and adjust as follows:

Clock type - 24 hour or 12 hour with AM/PM indication.

The factory pre-set is 24 hour. To convert to 12 hour, press and

hold down the NEXT and DAY buttons until the display changes,

then release. (Repeat to return to a 24 hour clock.)

Temperature display - °C or °F

The factory pre-set is °C. To convert to display all temperatures i n

°F, press and hold down the DAY and COPY buttons until the

display changes. (Repeat to return to a °C display.)

16. Check the existing space temperature by pressing and holding

down the two buttons: NEXT and COPY, until the display changes from

time to temperature.

17a. If the set temperature is below the space temperature, use the

button to raise the set temperature. The flame symbol will appear in the

display. Check that the heating plant operates correctly.

17b. If the set temperature is above the space temperature, use the

button to lower the set temperature below the space temperature. The

flame symbol will disappear. Check that the heating plant does not

operate.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Danfoss TP75-RF Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Danfoss TP75-RF

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info