Bedienungsanleitung Dashcam Mini 0803 (Seite 7 von 10) (Englisch)

652650

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

Micro SD card and installed on the computer).

Note: The recorder produces files that can provide excellent seamless playback (with no gaps

between files). However, while the supplied QtPlayer is fine for playing individual files, it is not

so good for a group of files, as there will be a gap/interruption between each file during

playback. There are other GPS players available without this shortcoming, or the files can be

used in a video editing package and played seamlessly via that (e,g: Pinnacle Studio 15, which

works fine for this).

Connecting the Recorder to a Standard SD TV

(Via the AV port (3))

Connect your recorder to the Standard TV via an Accessory AV cable (1296P recording is disabled).

Connecting the Recorder to HDTV

When connecting to HDTV, you can use high resolution to display video files or pictures. Use a HDMI

cable to connect the recorder video/audio signal to the HDTV (recording is disabled).

Installation in a Vehicle

It is preferable to locate the recorder behind the mirror, on the opposite side to the driver. This will

minimize any distraction from the screen and flashing recording light.

Notes:

1. A ‘fine’ marker pen will be useful to mark the final fixing point on the windscreen, before

removing the adhesive pad cover.

2. An external monitor with a larger screen would also assist in finding the best level location. This

can be plugged into the A/V port (3) via a 3.5mm ‘Stereo’ plug (inner is audio, outer is video).

Connect the recorder to the car Aux socket, via the cable provided. Switch on the ignition to auxiliary

power mode and when the recorder boots up and starts recording, press ‘OK’ to stop it recording.

Place it on the windscreen behind the mirror and locate it in the best location for a clear view of the

road (take care to avoid any items in the center that could mask the view, such as a rain sensor).

Important: Most monitor screens tend to have about 4% over scan, so an obstruction not visible on the

recorder monitor, could mask the edge of the view seen via a computer player.

Marking the Final Location: As there is a little bit of ‘give’ between the mounting bracket and the

recorder, it is advisable to hold the recorder by the mounting bracket when you place it at the final

position.

Ensure that it is level and mark the final position with the pen and make a test recording to confirm the

view is level and free from obstruction. Then remove the backing strip from the pad and carefully

stick the mounting bracket to the windscreen (it is easier to do this with the bracket separated from the

recorder).

Run the power cable to the Aux socket, preferably behind the trim on the opposite side to the driver.

Reconnect the recorder and power it up and when it starts recording, press ‘OK’ to stop it. Then select

Menu and set ‘Auto Power Off’ and ‘Power Off Screen’, to something other than ‘Never’ (e.g. the

default of 1min)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dashcam Mini 0803 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info