Bedienungsanleitung De Dietrich Gas 610 ECO (Seite 23 von 76) (Englisch)

481718

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

De Dietrich Gas 310/610 ECO

7.3.6 Conventional Chimney & CLV Systems Application Requirements:

Warning:

The boiler should never be operated in a negative building pressure. Caution should be exercised with

exhaust fans, air handling & other devices, that could affect the buildings air pressure or combustion air

supply. All venting must be arranged to avoid and prevent the accumulation of flue gas condensation.

An improperly sealed venting system could result in carbon monoxide poisoning; ensure adequate

support and fastening of the system. Ensure venting can safely exhaust all flue gases to the outside in a

safe and effective manner. Do not puncture or drill holes in any portion of the venting, the boiler is

equipped with a pressure and emission test port.

Venting lengths values must be between equivalent lengths show in table 04a-b. Any horizontal runs of

the venting must slope towards the boiler ½” per linear foot. The length in the tables apply to each vent

length separately (air intake and flue gas exhaust)

Exterior Venting:

Any portion of the venting exposed the outside climate shall be suitable for exterior applications.

Conventional Chimney applications:

This venting system uses a single vent to discharge all flue

gases to the outside vertically, combustion air provided with

the boiler room, the air source must be sized in accordance to

national codes CSA B149 & ANSI Z223.1 or local codes

having jurisdiction, more than one source may be required.

Conventional Chimney with direct vent (sealed

combustion air) applications:

This venting system uses either a co-axle or single vent for

both the air intake and the flue gas exhaust; the boiler room

does not require a combustion air source, as all air for

combustion is taken from the outside source.

Note: All lengths shown in table 04a-b are for a single boiler only. For multiple boilers (cascade)

common venting systems consult DDR Americas Inc. for assistance.

Chimney Application [room supplied combustion air]

Gas

310/610

Model

Vent ø

Vent

Length

[Min]

Vent

Length

[Max]

90°

Elbow =

Length

45°

Elbow =

Length

inch mm Ft. m Ft. m Ft. m Ft. m

310-5

10 250 5 1.5 250 76 12 3.5 6.5 2

310/610-6

310/610-7

310/610-8

310/610-9

Table 04[a] - venting length chart. Table also applies to Gas 610 models.

Chimney application with direct vent (sealed combustion air)

Gas

310/610

Model

Vent ø

Vent

Length

[Min]

Vent

Length

[Max]

90°

Elbow =

Length

45°

Elbow =

Length

inc

Ft.

310-5

10 250 5 1.5 200 60 12 3.5 6.5 2

310/610-6

310/610-7

310/610-8

310/610-9

Table 04[b] - venting length chart. Table also applies to Gas 610 models.



L = Max

Gas310 Eco Boiler

[Left hand version shown]

Convention Chimney application with

room supplied combustion air

Not shown air intake filter (recommended)

Fig. 7(a)



L = Max

Gas310 Eco Boiler

[Left hand version shown]



Convention chimney application with

Direct vent (Sealed Combustion Air) supply

Fig. 7(b)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

De Dietrich Gas 610 ECO Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info