Bedienungsanleitung De Walt D25500K T-3 (Seite 32 von 132) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

591271

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

ENGLISH

OPERATION

Instructions for Use

WARNING:

• Always observe the safety

instructions and applicable

regulations.

• For your own safety, always use the

tool with both hands.

• Be aware of the location of pipework

and wiring.

• Apply only a gentle pressure to

the tool (approx. 20 kg). Excessive

force does not speed up drilling

or chiselling but decreases tool

performance and may shorten

tool life.

Proper Hand Position (ﬁ g. 1)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the

side handle (h), with the other hand on the main

handle (l).

Switching On and Off (ﬁ g. 1)

1. To switch on the tool, press the on/off

switch (a).

2. To stop the tool, release the switch.

Drilling with a Solid Bit (ﬁ g. 1)

1. Insert the appropriate drill bit.

2. Set the mode selector switch (d) to the

“hammerdrilling” position.

3. Set the electronic speed and impact control

dial (b).

4. Fit and adjust the side handle (h).

5. If necessary, set the drilling depth.

6. Mark the spot where the hole is to be drilled.

7. Place the drill bit on the spot and switch on the

tool.

8. Always switch off the tool when work is finished

and before unplugging.

Drilling with a Core Bit (ﬁ g. 1)

1. Insert the appropriate core bit.

2. Assemble the centerdrill into the core bit.

3. Set the mode selector switch (d) to the

“hammerdrilling” position.

4. Turn the electronic speed and impact control

dial (b) to a medium or high speed setting.

5. Fit and adjust the side handle (h).

6. Place the centerdrill on the spot and switch on

the tool. Drill until the core penetrates into the

concrete approx. 1 cm.

7. Stop the tool and remove the center drill. Place

the core bit back into the hole and continue

drilling.

NOTE: When drilling through a structure thicker

than the depth of the core bit, break away the

round cylinder of concrete or core inside the bit

at regular intervals.

8. To avoid unwanted breaking away of concrete

around the hole, first drill a hole the diameter of

the centerdrill completely through the structure.

Then drill the cored hole halfway from each side.

9. Always switch off the tool when work is finished

and before unplugging.

Chipping and Chiselling (ﬁ g. 1)

1. Insert the appropriate chisel and rotate it by

hand to lock it into one of 8 positions.

2. Set the mode selector switch (d) to the

“hammering only” position.

3. Set the electronic speed and impact control

dial (b).

4. Fit and adjust the side handle (h).

5. Switch on the tool and start working.

6. Always switch off the tool when work is finished

and before unplugging.

MAINTENANCE

Your DEWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing set-ups

or when making repairs. Be sure the

trigger switch is in the OFF position. An

accidental start-up can cause injury.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

De Walt D25500K T-3 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info