Bedienungsanleitung De Walt D25762K T-1 (Seite 36 von 158) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

591299

Zoom out

Zoom in

Vorherige Seite

1/158

Nächste Seite

ENGLISH

D25870 (FIG. 2B)

1. Unscrew the side handle knob (p).

2. Slide the side handle assembly onto the

machine locating the steel ring (j) in the

mounting area (y). The correct position of the

side handle is between head and middle of the

tube.

3. Adjust the side handle (c) to the desired angle.

4. Slide and rotate the side handle to the desired

position.

5. Lock the side handle in place by tightening the

knob (p).

Inserting and Removing SDS Max

Accessories (ﬁ g. 1, 4A, 4B)

This machine uses SDS Max

bits and chisels (refer

to the inset in figure 4B for a cross-section of an

SDS Max

bit shank).

1. Clean the bit shank.

2. Pull back the locking sleeve (o) and insert the bit

shank.

3. Turn the bit slightly until the sleeve snaps into

position.

4. Pull on the bit to check if it is properly locked.

The hammering function requires the bit to be

able to move axially several centimetres when

locked in the tool holder.

5. To remove a bit pull back the tool holder locking

sleeve/collar (o) and pull the bit out of the tool

holder (l).

Selecting the Operating Mode

(ﬁ g. 1)

Hammerdrilling:

D25711, D25712, D25713, D25762, D25763

for concrete, brick, stone and masonry

drilling operations.

Hammering only:

for chiselling and demolition applications.

In this mode the tool can also be used as

a lever to free a jammed drill bit.

1. To select the operating mode, rotate the mode

selector switch (f) until it points to the symbol of

the required mode.

It may be neccessary to twist the tool holder (l)

slightly to allow the mode selector switch (f) to

pass the position.

2. Check that the mode selector switch (f) is

locked in place.

Indexing the Chisel Position

(ﬁ g. 5)

The chisel can be indexed and locked into 24

different positions.

1. Rotate the mode selector switch (f) until it points

towards the

position.

2. Rotate the chisel in the desired position.

3. Set the mode selector switch (f) to the

“hammering only” position.

4. Twist the chisel until it locks in position.

Setting the Electronic Speed and

Impact Control Dial (ﬁ g. 1, 3)

Turn the dial (g) to the desired level. Turn the dial

upwards for higher speed and downwards for

lower speed. The required setting is a matter of

experience, e.g.

– when chiselling or drilling in soft, brittle materials

or when minimum break-out is required, set the

dial to a low setting;

– when breaking or drilling in harder materials, set

the dial to a high setting.

Setting the Two Stage Mechanical

Clutch (ﬁ g. 3)

D25712, D25713, D25762, D25763

NOTICE: Always turn the tool off before

changing torque control settings or

damage to the tool may result.

Move the torque control lever (t) to setting 40Nm or

80Nm as needed for application.

• Clutch Setting 40Nm (u) is designed for most

drilling applications and is designed to easily

clutch out when the drill bit encounters re-bar or

other foreign substances.

• Clutch Setting 80Nm (v) is designed for higher

torque applications such as core-bits and deep

hole drilling and is designed to clutch out at a

higher torque threshold.

NOTE: If it is not possible to select position 80Nm

run the unit under load and try again.

Each time the tool is plugged in, it will automatically

default to clutch setting 1 into clutch setting 40Nm

(u), the most sensitive setting.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

De Walt D25762K T-1 Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von De Walt D25762K T-1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info