Bedienungsanleitung Definitive Technology BP-8060ST (Seite 3 von 12) (Englisch, Französisch, Spanisch)

582016

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Connecting Your Loudspeakers

Figure 3 – Wiring and Polarity

Wiring Options: High Level, High Level and LFE w/ “Y” Connector

VERY IMPORTANT:

Do not use your receiver’s auto setup functions as they are often

ineffective in setting up and adjusting speakers with built-in

powered subwoofers!

Use the manual speaker setup func-

tions in your receiver to set speaker

configuration, speaker distance and

channel balance. Consult your

receiver’s or processor’s manual to

learn how to access and use the setup

menus. Use the settings called for in

Figure 4.

Powering the Active Subwoofer

Your Bipolar STs contain a built-in subwoofer amplifier that must be plugged into

an electrical socket. When powering up from being unplugged, the LED on the

amplifier panel will flash for 30 seconds while the firmware is loading. The

Bipolar ST has a special circuit which automatically tur

ns on when a signal is fed

to the loudspeaker. The LED on the back panel will light up when a signal is

sensed and the amplifier turns on. After the cessation of a signal, it may take up

to an hour for the amplifier to turn off. Due to stray radio signals (RF) in your

area, the LEDs may not turn off. Do not be concerned, the amplifiers draw little

power when they are idle.

Setting Your Speakers’ Low-Frequency Level Control

Your Bipolar STs have bass level controls which allow you to adjust the output

level of the powered subwoofers to match your room and personal listening

preferences. Please note that there are no controls to

vary the crossover points or phase. The crossover

points and phase have been factory-calibrated to

provide perfect blending. We suggest beginning with

the level control set at approximately 12 o’clock.

Each speaker’s bass controls can also be set differently

in order to allow you to compensate for asymmetrical

positioning of the speakers in your room (i.e., when

one is closer to a side wall or corner, etc.).

Complete Home Theater System

We strongly suggest that you use matching Definitive center channel and

rear/surround speakers to complete your Definitive home theater system. Please

note that you can use Definitive Bipolar SuperTowers as rear or side surround

speakers with excellent results for both music and movies.

Troubleshooting

If you experience any difficulties with your Bipolar ST loudspeakers, try the

suggestions below. If you still have problems, contact your Definitive Technology

Authorized Dealer for assistance.

Audible distortion when the speakers are playing at loud levels is caused

by turning up your receiver or amplifier louder than the receiver or the

speakers are capable of playing. Most receivers and amplifiers put out their

full-rated power well before the volume control is turned all the way up, so

the position of the volume control is a poor indicator of its power limit. If

your speakers distort when you play them loud, turn the volume down!

2. If you experience a

lack of bass, it is likely that one speaker is out of phase

(polarity) with the other and needs to be rewired with closer attention to

connecting positive to positive and negative to negative on both channels.

Most speaker wir

e has some indicator (such as color

-coding, ribbing or

writing) on one of the two conductors to help you maintain consistency.

It is essential to connect both speakers to the amplifier in the same way

(in phase).

Make sur

e all your system inter

connects and power cor

ds ar

e solidly in place.

4. Should you hear

hum or noise coming from your speakers, try plugging

the speakers’ power cords into a different AC circuit than your amplifier.

The system has sophisticated

inter

nal pr

otection cir

cuitry

. If for some

reason the protection circuitry trips, turn off your system and wait five

minutes befor

e tr

ying the system again. If the speakers’ built-in amplifier

should over-heat, the system will turn off until the amplifier cools down

and resets.

6. Check to be sure that your power cord has not been damaged.

7. Check that no foreign objects or liquid has entered the speaker cabinet.

If you cannot get the subwoofer driver to turn on or if

no sound comes out

and you are sure the system is set up properly, please bring the loudspeaker

to your Definitive Technology Authorized Dealer for assistance; call first.

RECE IV ER/

AMPL IF IE R

Receiver/Amplifier

Strip 1/4" (6mm) wire.

dentify markings on wire and assign +/-.

Ensure that the speaker is always con-

nected to the receiver or amplifier + to +

and – to –.

Speaker Setup

Speaker Sub

Lar

ge Y

Subwoofer

level

Subwoofer

level

LFE

speaker output

LFE

Receiver/Amplifier

Right Left

“Y” Connector *available from dealer

Subwoofer

level

on/off LED

LFE

Connection Option 1

Receiver/Amplifier

speaker output

Speaker Setup

Speaker Sub

Large No

Figur

e 4 – Receiver Settings

LFE

Connection Option 2

Min Max

1. Unscrew binding post and insert wire.

2. Tighten until wire is secure.

BIPOLAR SUPERTOWER

OWNER’S MANUAL

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Definitive Technology BP-8060ST Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info