Bedienungsanleitung Defort DAG-600-B (Seite 6 von 56) (Alle Sprachen)

555479

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Angle grinder

INTENDED USE

This tool is intended for grinding, cutting and deburr-

ing metal and stone materials without the use of water;

with the appropriate accessories the tool can also be

used for brushing and sanding

TECHNICAL SPECIFICATIONS 1

PRODUCT ELEMENTS 2

1. Spindle

2. Clamping ﬂ ange

3. Spanner

4. Spindle-lock button

5. Auxiliary handle

6. Safety guard

7. Mounting ﬂ ange

8. On/off locking switch

SAFETY

WARNING! Read all instructions. Failure to follow all

instructions listed below may result in electric shock,

ﬁ re and/or serious injury.

 Only use this tool for dry grinding/cutting

 Only use the ﬂ anges which are supplied with this

tool

 This tool should not be used by people under the

age of 16 years

 Always disconnect plug from power source before

making any adjustment or changing any accessory

ACCESSORIES

 Use the original SBM Group accessories which can

be obtained from your SBM Group dealer

 For mounting/using non- SBM Group accessories

observe the instructions of the manufacturer con-

cerned

 Use only accessories with an allowable speed

matching at least the highest no-load speed of the

tool

 Do not use damaged, deformed or vibrating grind-

ing/ cutting discs

 Handle and store grinding/cutting discs carefully to

avoid chipping and cracking

 Protect accessories from impact, shock and grease

 Do not use a grinding/cutting disc that is larger than

the maximum recommended size

 Only use grinding/cutting discs with a hole diameter

which ﬁ ts mounting ﬂ ange (7) without play; never use

reducers or adaptors to ﬁ t large-hole grinding/cut-

ting discs

 Never use grinding/cutting discs with a threaded

hole, of which the thread is not long enough to ac-

cept the spindle length of the tool

 Never use accessories with a “blind” threaded hole

smaller than M14 x 21 mm

OUTDOOR USE

 Connect the tool via a fault current (FI) circuit break-

er with a triggering current of 30 mA maximum

 Only use an extension cord which is intended for

outdoor use and equipped with a splashproof cou-

pling-socket

BEFORE USE

 Before using the tool for the ﬁ rst time, it is recom-

mended to receive practical information

 Do not work materials containing asbestos (asbes-

tos is considered carcinogenic)

 Take protective measures when during work dust

can develop that is harmful to one’s health, combus-

tible or explosive (some dusts are considered carci-

nogenic); wear a dust mask and work with dust/chip

extraction when connectable

 Be careful of hidden electrical wires or gas- and wa-

ter pipes; check the work area, for instance with a

metal detector

 Be careful when cutting grooves, especially in sup-

porting walls (slots in supporting walls are subject to

country- speciﬁ c regulations; these regulations are

to be observed under all circumstances)

 Clamp the workpiece in case it does not remain

stationa ry from its own weight

 Do not clamp the tool in a vice

 Use completely unrolled and safe extension cords

with a capacity of 16 Amps (UK 13 Amps)

 Wear protective glasses and gloves, hearing protec-

tion and sturdy shoes; when necessary, also wear

an apron

 Always mount auxiliary handle (5) and protective

guard (6); never use the tool without them

 Be sure tool is switched off when plugging in

DURING USE

 Always keep the cord away from moving parts of the

tool; direct the cord to the rear, away from the tool

 If the cord is damaged or cut through while working,

do not touch the cord, but immediately disconnect

the plug; never use the tool with a damaged cord

 Push spindle-lock button (4) only when spindle (1) is

at a standstill

 Keep hands away from rotating accessories

 When grinding metal, sparks are generated; keep

other persons and combustible material from work

area

 In case of electrical or mechanical malfunction,

immediately switch off the tool and disconnect the

plug

 In case the cutting disc is blocked, resulting in jerk-

ing forces on the tool, immediately switch off the

tool

 In case of current interruption or when the plug is

accidentally pulled out, unlock the on/off switch (8)

immediately and put it in the OFF-position in order to

prevent uncontrolled restarting

 Do not apply so much pressure on the tool that it

comes to a standstill

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Defort DAG-600-B Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info