Bedienungsanleitung Defort DCS-161N (Seite 7 von 72) (Alle Sprachen)

555499

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

build-up of debris)

• Lower guard should be retracted manually only

for special cuts such as plunge cuts and compound

cuts; raise lower guard by retracting handle and as

soon as blade enters the material, the lower guard

must be released (for all other sawing, the lower guard

should operate automatically)

• Always observe that the lower guard is covering

the blade before placing saw down on bench or

ﬂ oor (an unprotected, coasting blade will cause the

saw to walk backwards, cutting whatever is in its path;

be aware of the time it takes for the blade to stop after

switch is released)

• Avoid damage that can be caused by screws, nails

and other elements in your workpiece; remove them

before you start cutting

• When you put away the tool, switch off the motor and

ensure that all moving parts have come to a complete

standstill

• Use completely unrolled and safe extension cords

with a capacity of 16Amps (U.K. 13Amps)

• In case of jamming or electrical or mechanical

malfunction, immediately switch off the tool and

disconnect the plug

• The SBM Group can assure ﬂ awless functioning of

the tool only when original accessories are used

• Use only accessories with an allowable speed

matching at least the highest no-load speed of the tool

• Never use the tool without the original protection

guard system

• This tool should not be used by people under the age

of 16 years

• The noise level when working can exceed 85 dB(A);

wear ear protection

• If the cord is damaged or cut through while working,

do not touch the cord, but immediately disconnect the

plug

• Never use tool when cord is damaged; have it

replaced by a qualiﬁ ed person

• Always check that the supply voltage is the same as

the voltage indicated on the nameplate of the tool (tools

with a rating of 230V or 240V can also be connected to

a 220V supply)

• This tool is not suitable for wet cutting

• After switching off your circular saw, never stop the

rotation of the saw blade by a lateral force applied

against it

• Never use circular saw blades made of high speed

steel (HSS)

• Never use grinding/cutting discs with this tool

• Do not work materials containing asbestos

(asbestos is considered carcinogenic)

• Take protective measures when during work

dust can develop that is harmful to one’s health,

combustible or explosive (some dusts are considered

carcinogenic); wear a dust mask and work with dust/

chip extraction when connectable

• Do not attempt to cut extremely small workpieces

• Remove all obstacles on top of as well as underneath

the cutting path before you start cutting

• Do not work overhead with the tool

• Only use a saw table provided with a switch that

prevents restarting of the motor after interruption of

voltage

• Only use a saw table provided with a kerf guide

• Always disconnect plug from power source

before making any adjustment or changing any

accessory

WHEN CONNECTING NEW 3-PIN PLUG (U.K.

ONLY):

• Do not connect the blue (= neutral) or brown (= live)

wire in the cord of this tool to the earth terminal of the

plug

• If for any reason the old plug is cut off the cord

of this tool, it must be disposed of safely and not left

unattended

Your machine is double insulated in accord-

ance with EN 50144; therefore no earthwire

is required.

MAINTENANCE

Make sure that the machine is not live when

carrying out maintenance work on the motor.

Regularly clean the machine housing with a soft cloth,

preferably after each use. Keep the ventilation slots free

from dust and dirt.If the dirt does not come off use a soft

cloth moistened with soapy water. Never use solvents

such as petrol, alcohol, ammonia water, etc. These sol-

vents may damage the plastic parts.

The machine requires no additional lubrication.

Should a fault occur, e.g. after wear of a part, please

contact your local SBM Group dealer.

ENVIRONMENT

In order to prevent the machine from damage during

transport, it is delivered in a sturdy packaging. Most of

the packaging materials can be recycled. Take these

materials to the appropriate recycling locations. Take

your unwanted machines to your local SBM Group

dealer. Here they will be disposed of in an environmen-

tally safe way.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Defort DCS-161N Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info