Bedienungsanleitung Defort DET-100 (Seite 7 von 68) (Alle Sprachen)

555700

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

OPERATION

STARTING OPERATION

● Observe correct mains voltage! The voltage of the

power source must agree with the voltage speciﬁ ed on

the nameplate of the machine. Power tools marked with

230 V can also be operated with 220 V.

SWITCHING ON AND OFF

At ﬁ rst, ﬁ rmly place the tacker head against the workpiece

until it is pushed in a few millimeters. Afterwards, brieﬂ y

press the trigger and then release again.

The trigger lock, which is connected with the movable

tacker head, prevents unintentional shot actuation when

the trigger is inadvertently pressed.

For rapid working, keep the trigger pressed. Position the

machine and press the tacker head ﬁ rmly against the work-

piece until the shot is actuated. After the shot, move the

tacker to the next location and press the tacker head ﬁ rmly

onto the workpiece again.

WORKING ADVICE

● This machine is not suitable for working with 19 mm sta-

ples. Therefore, do not use the machine to fasten ceiling

panelling with proﬁ led wood or grooves.

Avoid blank shots in order to reduce the wear of the impact

striker.

The machine is designed only for intermittent operation

and will warm up with continuous use. The tacking force

is reduced as a result of heating up. Therefore, allow the

machine to cool off after 15 minutes (maximum) of continu-

ous operation.

MAINTENANCE AND SERVICE

MAINTENANCE AND CLEANING

● Before any work on the machine itself, pull the mains

plug.

● For safe and proper working, always keep the machine

and ventilation slots clean. If the machine should fail

despite the care taken in manufacturing and testing pro-

cedures, repair should be carried out by an after-sales

service centre for SBM Group.

SAFETY WARNINGS FOR TACKERS

● Always assume that the tool contains fasteners. Care-

less handling of the tacker can result in unexpected

ﬁ ring of fasteners and personal injury.

● Do not point the tool towards yourself or anyone nearby.

Unexpected triggering will discharge the fastener caus-

ing an injury.

● Do not actuate the tool unless the tool is placed ﬁ rmly

against the workpiece. If the tool is not in contact with

the workpiece, the fastener may be deﬂ ected away from

your target.

● Disconnect the tool from the power source when the

fastener jams in the tool. While removing a jammed

fastener, the tacker may be accidentally activated if it is

plugged in.

● Use caution while removing a jammed fastener. The

mechanism may be under compression and the fastener

may be forcefully discharged while attempting to free a

jammed condition.

● Do not use this tacker for fastening electrical cables. It

is not designed for electric cable installation and may

damage the insulation of electric cables thereby causing

electric shock or ﬁ re hazards.

● Use suitable detectors to determine if utility lines are hid-

den in the work area or call the local utility company for

assistance. Contact with electric lines can lead to ﬁ re

and electric shock. Damaging a gas line can lead to ex-

plosion. Penetrating a water line causes property dam-

age or may cause an electric shock.

● Secure the workpiece. A workpiece clamped with clamp-

ing devices or in a vice is held more secure than by

hand.

Products sold in GB only: Your product is ﬁ tted with an BS

1363/A approved electric plug with internal fuse (ASTA ap-

proved to BS 1362).

If the plug is not suitable for your socket outlets, it should

be cut off and an appropriate plug ﬁ tted in its place by an

authorised customer service agent. The replacement plug

should have the same fuse rating as the original plug.

The severed plug must be disposed of to avoid a possible

shock hazard and should never be inserted into a mains

socket elsewhere.

Products sold in AUS and NZ only: Use a residual cur-

rent device (RCD) with a rated residual current of 30 mA

or less.

ASSEMBLY

● Before any work on the machine itself, pull the mains

plug.

● Press on both sides of the magazine slider and pull out

the magazine.

● Insert the staple strip or the nail strip. Hold the tacker at

a slight angle when inserting the nail strip, so that the

nails face against the sidewall.

● Slide in the magazine until the closure on the magazine

slider engages.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Defort DET-100 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info