Bedienungsanleitung Defort DLM-2600-G (Seite 14 von 32) (Alle Sprachen)

555837

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

STORAGE INSTRUCTIONS

(OFF SEASON)

The following steps should be taken to prepare lawn

mower for storage.

1. Following the ﬁ nal cut of the season allow the fuel

tank to run dry.

2. Clean and lubricate mower thoroughly as described

in the lubrication instructions.

3. Refer to engine manual for correct engine storage

instructions.

4. Lightly coat mower’s cutting blade with chassis

grease to prevent rusting.

5. Store mower in a dry, clean area.

NOTE:

- When storing any type of power equipment

in an unventilated or material storage shed;

- Care should be taken to rust-proof the equipment.

Using a light oil or silicone, coat the equipment,

especially cables and all moving parts.

- Be careful not to bend or kink cables.

- If the starter rope becomes disconnected from rope

guide on handle, disconnect and ground the spark

plug wire, Depress the blade control handle and pull

the starter rope out from engine slowly. Slip the starter

rope into the rope guide bolt on handle.

ENGINE AIR CLEANER

CAUTION: Do not allow dirt or dust to clog

the air ﬁ lter foam element.

The engine air cleaner element must be

serviced (cleaned) after 25 hours normal mowing. The

foam element must be serviced regularly if the mower

is used in dry dusty conditions.

TO CLEAN AIR FILTER

1. Remove screw.

2. Remove cover.

3. Wash ﬁ lter element in soap water. DO NOT USE

GASOLINE!

4. Air dry ﬁ lter element.

5. Place a few drops of SAE30 oil on the foam ﬁ lter and

squeeze tightly to remove any excess oil.

6. Reinstall ﬁ lter.

NOTE: Replace ﬁ lter if frayed, torn, damaged

or unable to be cleaned.

CUTTING BLADE

CAUTION: Be sure to disconnect and ground

the spark plug wire before working on the

cutting blade to prevent accidental engine

starting. Protect hands by using heavy gloves or a rag

to grasp the cutting blades.

WARNING: Periodically inspect the blade

adapter for cracks, especially if you strike a

foreign object. Replace when necessary. For

best results your blade should be sharp. The blade

may be resharpened by removing it and either grinding

or ﬁ ling the cutting edge keeping as close to the original

bevel as possible. It is extremely important that each

cutting edge receives an equal amount of grinding to

prevent an unbalanced blade. Improper blade balance

will result in excessive vibration causing eventual

damage to the engine and mower.

BLADE MOUNTING TORQUE

Center Bolt must be tightened to 35 - 45 Nm torque. To

insure safe operation of your unit. ALL nuts and bolts

must be checked periodically for correct tightness. After

prolonged use, especially in sandy soil conditions, the

blade will become worn and lose some of the original

shape. Cutting efﬁ ciently will be reduced and the blade

should be replaced. Replace with an approved factory

replacement blade only. Possible damage resulting

from blade unbalance condition is not the responsibility

of the manufacturer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Defort DLM-2600-G Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info