Bedienungsanleitung Defort DMS-1200-C (Seite 12 von 32) (Deutsch, Englisch, Französisch)

555810

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

– Determine the cause of the blockage and correct it.

INTEGRATED DUST EXTRACTION

– Mount the dust bag 18 onto the sawdust ejector 21.

During sawing, the dust bag must never come into con-

tact with the movable machine parts. Always empty the

dust bag in good time.

EXTERNAL DUST EXTRACTION

For dust extraction, a vacuum hose can also be con-

nected to the dust ejector 21.

The vacuum cleaner must be suitable for the material

being worked. When vacuuming dry dust that is espe-

cially detrimental to health or carcinogenic, use a spe-

cial vacuum cleaner.

CHANGING THE TOOL

● Before any work on the machine itself, pull the mains

plug.

● When mounting the saw blade, wear protective

gloves. Danger of injury when touching the saw blade.

Use only saw blades whose maximum permitted speed

is higher than the no-load speed of the power tool.

Use only saw blades that correspond with the charac-

teristic data given in these operation instructions and

that are tested and marked in accordance with EN

847-1.

Use only saw blades recommended by the tool manu-

facturer, and suitable for sawing the materials to be

cut.

MOUNTING THE SAW BLADE

If required, clean all parts to be mounted prior to as-

sembly.

– Press lever 3, swing back the retracting blade guard

5 to the stop and hold it in this position.

– Place the new saw blade onto the interior clamping

ﬂ ange.

● When mounting the saw blade, pay attention that the

cutting direction of the teeth (arrow direction on the saw

blade) corresponds with the direction of the arrow on

the blade guard!

– Slowly guide the retracting blade guard downward

again.

– Place on the clamping ﬂ ange and the screw.

Press the spindle lock 28 until it engages and tighten

the screw turning in anticlockwise direction.

OPERATION

● Before any work on the machine itself, pull the mains

plug.

ADJUSTING THE CUTTING ANGLE

● When adjusting the cutting angle, never actuate

the On/Off switch 19. Danger of injury if the machine

should accidentally start.

ADJUSTING THE CUTTING ANGLE

● When adjusting the cutting angle, never actuate

the On/Off switch 19. Danger of injury if the machine

should accidentally start.

ADJUSTING HORIZONTAL MITRE ANGLES

The horizontal mitre angle can be set in the range from

FUNCTIONAL DESCRIPTION

Read all safety warnings and all instructions. Failure

to follow the warnings and instructions may result in

electric shock, ﬁ re and/or serious injury.

INTENDED USE

The power tool is intended as a stationary machine

for making straight lengthways and crossways cuts in

wood. In this, mitre angles from –46° to +46° as well as

bevel angles from 0° to 45° are possible.

The capacity of the power tool is designed for sawing

hardwood and softwood.

The power tool is not suitable for cutting aluminium or

other non-ferrous metals or alloys.

ASSEMBLY

● Avoid unintentional starting of the machine. During

assembly and for all work on the machine, the power

plug must not be connected to the mains supply.

Note: Check the power tool for possible damage. Be-

fore further use of the machine, check that all protective

devices are fully functional. Any lightly damaged parts

must be carefully checked to ensure ﬂ awless opera-

tion of the tool. All parts must be properly mounted and

all conditions fulﬁ lled that ensure faultless operation.

Damaged protective devices and parts must be imme-

diately replaced by an authorised service centre.

MOUNTING TO A WORKING SURFACE

● To ensure safe handling, the machine must be

mounted on a level and stable surface (e. g., work-

bench) prior to using.

– Carefully remove all parts included in the delivery

from their packaging.

– Remove all packaging material from the machine and

the accessories provided.

– Fasten the power tool with suitable screw fasteners

to the working surface. The holes 12 serve for this pur-

pose.

DUST/CHIP EXTRACTION

Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harm-

ful to one’s health. Touching or breathing-in the dusts

can cause allergic reactions and/or lead to respiratory

infections of the user or bystanders.

Certain dusts, such as oak or beech dust, are con-

sidered as carcinogenic, especially in connection

with wood-treatment additives (chromate, wood pre-

servative). Materials containing asbestos may only be

worked by specialists.

– Always use dust extraction.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 ﬁ lter-class respira-

tor.

Observe the relevant regulations in your country for the

materials to be worked.

The dust/chip extraction can be blocked by dust, chips

or workpiece fragments.

– Switch the machine off and pull the mains plug from

the socket outlet.

– Wait until the saw blade has come to a complete

stop.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Defort DMS-1200-C Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info