Bedienungsanleitung Defort DPS-17N (Seite 8 von 92) (Alle Sprachen)

555779

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

How to use the energy station to start a vehicle

1. Connect the red cable (+) of the energy station to the

POSITIVE pole (+) of the vehicle battery.

2. Connect the black cable (-) of the energy station to

the vehicle's earthing strip or any other bare point

on the engine block (earth). Choose a point as far

away as possible from the battery in order to prevent

ignition of any explosive electrolytic gas which may

develop.

3. The switch (Figure 1 / Item 1) must be set to «ON»

position.

4. Turn the ignition key over to start position and wait

approx. 2 minutes.

DO NOT START THE ENGINE!

5. With the energy station connected, you can now try

to start the engine. Do not attempt to start the vehi-

cle for longer than 5 seconds because of the very

high current involved. If the engine fails to start, wait

for 3 minutes before next attempt.

6. First disconnect the pole clamp from the vehicle's

earthing strip (negative pole).

7. Then disconnect the jumper cable from the POSI-

TIVE pole (+) of the vehicle battery.

8. The energy station will need to be recharged after

giving this starting aid.

9. FOR USE AS AN ADAPTER

Please make sure that:

you only use 12V appliances

with a plug suitable for usein

the cigarette lighter.

The power station can be also used as an adapter to

connect to the external battery. Connect the station ca-

ble outputs to the positive and negative terminals of

your car

The power station can be also used as an adapter to

connect to the external battery. Connect the station ca-

ble outputs to the positive and negative terminals of

your car battery. The power from the battery is then

transferred to the power station outputs. Thus, you can

use the power from this external battery rather than

that from your power station.

11.12-VOLT COMPRESSOR

11.1 Filling tires

Note! Use a tire pressure gauge to check the actual tire

pressure at the nozzle. Observe the information in the

vehicle's owner manual concerning the ﬁ lling of tires.

1. Remove the valve cap from the valve.

2. Push the connector piece of the compressor all the

way down over the valve.

3. Secure the connector piece by ﬂ ipping back the

locking lever on top of the connector.

11.2 Filling air mattresses, etc.

Important! Because of the material composition of air

mattresses, rubber rafts, etc., obtaining an exact air

pressure read-out is not possible. Therefore, pay spe-

cial attention to ensure that you do not overﬁ ll these

objects, as they will burst!

• Select the appropriate adapter and insert it into the

connector piece of the air hose.

• Secure the connector piece by ﬂ ipping back the

locking lever on top of the connector

11.3 Starting up the compressor

Important! Please read the bulleted items listed un-

der 1. Important Notes» prior to starting up the com

pressor. Ensure that the com pressor cools down for

10 minutes after it has run for 20 minutes.

• Check the pressure gauge (Fig. 1/ltem 5) prior to

switching on.

• To switch on, ﬂ ip the ON/OFF switch (Fig. 1/ltem10)

to «l».

• To switch off, ﬂ ip the ON/OFF switch (Fig. 1/ltem10)

to «0».

12.MAINTENANCE AND CARE

• Be sure to switch off the energy station and discon-

nect all cables from the unit whenever you perform

any cleaning or maintenance work.

• As far as possible, use only a soft dry cloth without

any aggressive solvents to clean the surface. If ab-

solutely necessary, use a slightly dampened rag to

remove dirt.

13. REPAIR

Should the tool experience problems beyond those

mentioned above, let only an authorized professional

or the SBM Group customer service shop perform an

inspection.

14. DISPOSAL

The tool, accessories and packaging should be dis-

posed of in an environmentally-friendly fashion. Plas-

tic parts are coded for purposes of separation when

recycling.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Defort DPS-17N Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info