Bedienungsanleitung Defort DSG-80N (Seite 9 von 108) (Alle Sprachen)

555557

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

Never start or stop the spray gun while it is aimed at

the surface to be sprayed. Evenly control the speed of

movement of the spray gun. A fast speed of movement

over the surface will give a thin coat and aslowspeed

will givea heavy coat. Apply one coat at a time. If a fur-

ther coat is required, make sureyou observe the manu-

facturers drying time recommendations before apply-

ing a second coat. When spraying small areas, keep

the output control on a low setting. This will avoid using

too much paint and prevent overspray. Where possible,

avoid stopping and starting when spraying an object.

This can lead to too much, or not enough paint being

applied. Do not tip the spray gun to more than 45°

CLEANING AND MAINTENANCE F

Always remember to disconnect from the

mains supply before cleaning the spray gun

or paint container.

It is essential that the spray gun is cleaned thoroughly

after every use. Failure to clean it will almost certainly

result in blockages and it may not operate when you

next come to use it! The guarantee does not cover

cleaning a sprayer that has not been properly cleaned

by the user.

The following action must be taken after every

use.

1. Empty any remaining material from the container.

2. Clean the container thoroughly with the thinner

thatwas used.

3. Pour some thinner into the container and spray

through the spray gun until only clean thinner is

coming out of the nozzle.

4.Thoroughly clean the paint pick uppipeand ﬁ lter with

thinner.

5.Clean the basket and nozzle and remove any other

debris or paint that remains.

6. Turn the spray gun upside down and apply a few

drops of light oil to the two apertures (F). This will

lubricate the piston and cylinder.

If your spray gun should require extra internal

cleaning, it may be necessary to disassemble it. If

so the following action should be taken.

1. Remove the plug from the mains socket.

2. Remove paint container, pick up pipe and ﬁ lter.

3. Release the nozzle (H), valve (j), piston (K) and

spring (L).

4. Clean the cylinder (M) and all parts thoroughly with

solvent.

5. Apply a few drops of light lubricating oil to the pis-

ton, springand cylinder.

6. Reassemble the spray gun.

TROUBLE SHOOTING

Motor hums but does not spray or irregular spray-

ing.

1. Worn swirl head

Replace swirl head.

2. Pick up pipe not into the right position

Re-adjust pick up pipe.

3. Blocked pick up pipe

Clean with thinner.

4. Blocked nozzle

Clean nozzle.

5. Blocked ﬁ lter

Clean with thinner.

6. Control knob needs adjustment

Adjust.

Atomization is not good.

1. Volume adjustment is not correct.

Adjust

2. Paint too thick

Check viscosity of the paint

Over painting.

1. Spray gun not clean, or not lubricated, resulting in

piston being stuck in cylinder

Disassemble spray gun and dean with thinner.

2. Too much paint

Adjust the volume clockwise to reduce spraying.

Two t/i/n coats are better then one thick coat.

3. Viscosity too low

Check viscosity

Motor louderthan normal.

1. Spray gun not clean, or not lubricated, resulting in

piston being stuck in cylinder

Disassemble spray gun and clean with thinner.

No spray, no sound.

1. No electricity

Check power supply.

Operating sound not right.

1. Poor output adjustment

Re-adjust

2. Not enough paint in the container resulting in air

being sucked in.

Reﬁ ll with paint

3. Not diluting properly or not passing pick up pipe

completely.

Check pick up pipe and viscosity level.

«Orange Skin» excessive fogging.

1. Incorrectsolventis used

Use correct solvent

2. Spray gun too far from the surface.

Hold spray gun closer to Vie object

3. Paint too thick

Thin the paint

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Defort DSG-80N Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info