Bedienungsanleitung Dell XPS all types (Seite 58 von 69) (Englisch)

681828

Zoom out

Zoom in

Vorherige Seite

1/69

Nächste Seite

If a component fails the test, the test stops, the computer beeps, and an error code is displayed. Note the error code(s) and search for

solutions at www.dell.com/support or Contact Dell.

Follow the instructions on the screen to continue to the next test, retest the component that failed, or stop the test and restart the

computer. If the PSA completes successfully, the following message appears on your screen: No problems have been found with this

system so far. Do you want to run the remaining memory tests? This will take about 30 minutes or more. Do you want to continue?

(Recommended).

Press <y> to continue if you are experiencing memory issue, otherwise press <n> to nish the test.

NOTE: Press Esc anytime during the test to abort testing and restart your computer.

Enhanced PSA

You can use the Enhanced Pre-Boot System Assessment (ePSA) to diagnose various hardware problems. The ePSA tests devices such as

the system board, keyboard, display, memory, hard drive, and so on.

NOTE: ePSA may not be supported on all computers.

The ePSA home screen is divided into three areas:

• Devices window—Appears on the left of the ePSA home screen. It displays all the devices in your computer and can be used to select

devices.

• Control window—Appears at the bottom-right of the ePSA home screen.

– Selecting the Thorough Test Mode check-box in the control window maximizes the extent and duration of the tests.

– Status bar appears at the bottom left side of the control window and indicates the overall completion of the tests.

– To test selected devices, click or tap Run Tests.

– To exit the ePSA and restart your computer, click or tap Exit.

• Status window—Appears on the right of the ePSA home screen.

The status area has four tabs:

• Conguration—Displays detailed conguration and status information about all devices that can be tested using ePSA.

• Results— Displays all tests that are executed, their activity, and results for each test.

• System Health—Displays the status of the battery, power adapter, fans, and so on.

• Event Log—Provides detailed information about all tests.

The Stat column displays the status of the tests.

LCD BIST

LCD BIST (Built‑In Self Test) helps you determine if a display problem is caused by the LCD or some other part. The test may displays

dierent colors and text on the screen and if you do not notice the problem during the test then the issue lies outside of the LCD.

NOTE

: Peripherals may have diagnostics specic to them. For more information, see the documentation of the peripheral.

Starting LCD BIST

1 Turn on or restart your computer.

2 Press F12 at the Dell logo to access the BIOS setup program.

NOTE

: If you wait too long and the operating system logo appears, continue to wait until you see the Windows desktop,

then restart your computer and try again.

3 Select Diagnostics and press Enter.

4 If you do not see colored lines on the screen, press N to enter the LCD BIST.

Troubleshooting

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dell XPS all types Seite 58

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info