Bedienungsanleitung DeLonghi Dinamica ECAM 350.55 (Seite 17 von 21) (Englisch)

687413

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

Ground too ne

Adjust mill

The grinding is too ne and the coee is deliv-

ered too slowly or not at all.

Repeat coee delivery and turn the grinding

adjustment dial (A5) (g. 7) one click clockwise

towards 7 while the coee mill is in operation.

If after making at least 2 coees delivery is

still too slow, repeat the correction procedure,

turning the grinding adjustment dial another

click until delivery is correct (see section “10.1

Adjusting the coee mill”. If the problem per-

sists, make sure the water tank (A17) is fully

inserted.

If the water softener lter (C4) is present, an

air bubble may have been released inside the

circuit, obstructing delivery.

Insert the hot water spout (C6) in the appli-

ance and deliver a little water until the ow

becomes regular.

Less coee Too much coee has been used.

Select a lighter taste by pressing (B7) or

reduce the quantity of pre-ground coee.

Insert water spout The hot water spout (C6) is not inserted or is

inserted incorrectly.

Fully insert the hot water spout (g. 4).

Insert milk container The milk container (D) is not inserted correctly. Insert the milk container as far as it will go (g.

16).

Insert infuser assembly The infuser (A20) has not been replaced after

cleaning.

Insert the infuser as described in section “14.9

Cleaning the infuser”.

Water circuit empty

Fill water circuit

Hot water

Conrm?

The water circuit is empty. Press OK (B3) to deliver water from the spout

(C6) until it ows out normally. If the problem

persists, make sure the water tank (A17) is fully

inserted.

Press OK to CLEAN The milk container (D) has been inserted with

the froth adjustment dial (D1) in the "CLEAN"

position.

To proceed with the CLEAN function press OK

or turn the froth adjustment dial to another

position.

Set dial to CLEAN

ESC to cancel

Milk has been delivered recently and the tubes

inside the milk container (D) must be cleaned.

Turn the froth adjustment dial (D1) to CLEAN

(g. 19).

Turn froth adjustment dial The milk container (D) has been inserted with

the froth adjustment dial (D1) in the "CLEAN"

position.

Turn the froth adjustment dial to one of the

milk froth positions.

Descale

ESC to cancel

OK to descale

(∼45 minutes)

The machine must be descaled. The descaling procedure described in section

“15. Descaling” needs to be performed.

Replace lter

ESC to cancel

OK to replace

The water softener lter (C4) is exhausted. Replace the lter or remove it as described in

section “17. Water softener lter”.

General alarm The inside of the appliance is very dirty. Clean the inside of the appliance thoroughly,

as described in section “14. Cleaning”. If the

message is still displayed after cleaning, con-

tact a service centre.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeLonghi Dinamica ECAM 350.55 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeLonghi Dinamica ECAM 350.55

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info