Bedienungsanleitung DeLonghi ECAM 26.455.B - PRIMADONNA S (Seite 19 von 22) (Englisch)

562572

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

5. Press the button to conrm the setting.

6. Press the MENU/ESC button to exit the menu.

The machine is now reprogrammed with the new water

hardness setting

WATER FILTER

Certain models are tted with a water softener lter. If this

is not the case with your model, you are recommended to

purchase one from De’Longhi

Customer Experience.

To use the lter correctly,

follow the instructions

below.

Installing the lter

1. Remove the lter from

the packaging.

2. Turn the date indicator

disk (see g. 33) until

the next 2 months of

use are displayed.

Please note

The lter lasts about two

months if the appliance is

used normally. If the coee

maker is left unused with the

lter installed, it will last a

maximum of three weeks.

3. Remove the tank from

the appliance and ll

with water.

4. Insert the lter in the

water tank and immerse

it completely for ten or

so seconds, sloping it to

enable the air bubbles

to escape (g. 34).

5. Insert the lter in the

lter housing (g. 35A)

and press as far as it will

go.

6. Close the tank with the

lid (g. 35B), then replace the tank in the machine.

When you install the lter, you must notify the appliance of its

presence.

7. Press the MENU/ESC button to enter the menu;

8. Press the MILK or CAPPUCCINO button (g. 8) until

“Install lter” is displayed;

9. Press the button;

Remove the water tank, empty, rinse under running

water, ll with clean water and replace.

“Rinsing... Conrm?” is displayed.

8. Empty the container used to collect the descaler solution

and replace it empty under the hot water spout.

9. Press the button to start rinsing.

Hot water ows out of the spout and the message

“Rinsing...” is displayed.

10. When the water tank is completely empty, “ Rinsing

Complete Conrm?” is displayed.

11. Press the button.

12. Insert the lter (if present) in the tank (see section

“Installing the lter” on page 18), ll the water tank again

and the appliance is ready for use.

SETTING THE WATER HARDNESS

The DESCALE message is displayed after a period of time

according to water hardness.

The machine is factory set for a hardness value of 4.

The machine can also be programmed according to the

hardness of the mains water in the various regions so that the

machine needs to be descaled less often.

Measuring water hardness

1. Remove the “total hardness test” indicator paper attached

to this manual from its pack.

2. Immerse the paper completely in a glass of water for one

second.

3. Remove the paper from the water and shake lightly.

After about a minute, 1, 2, 3, or 4 red squares form,

depending on the hardness of the water. each square

corresponds to one level.

soft water ●

slightly hard water

 ●●

hard water●●●

very hard water

●●●●

Set water hardness

1. Press the MENU/ESC button to enter the menu.

2. Press the MILK or CAPPUCCINO button to select “Water

Hardness”.

3. Conrm the selection by pressing the button.

4. Press the MILK or CAPPUCCINO button and set the

hardness shown by the indicator paper (see previous

section).

35A

35B

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeLonghi ECAM 26.455.B - PRIMADONNA S Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeLonghi ECAM 26.455.B - PRIMADONNA S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info