Bedienungsanleitung DeLonghi ESAM 5500 (Seite 19 von 26) (Englisch)

99881

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

wise then remove it.

2. Remove the milk spout and intake tube.

3. Remove the pointer by pulling it outwards.

4. Wash all the components thoroughly with hot

water and mild dish detergent. Make sure

there are no milk residues left inside the holes

and the groove on the fine end of the pointer.

5. Check that the

intake tube and

spout are not

clogged with

milk residues.

6. Replace the

pointer, milk

spout and intake tube.

7. Replace the milk container lid.

DESCALING

Descale the machine when the red light and the

message "DESCALE" flash on the display.

Important!

Descaler contains acids which

may irritate the skin and eyes. It is vital to respect

the manufacturer's safety warnings given on the

descaler pack and the warnings relating to the pro-

cedure to follow in the event of contact with the skin

and eyes.

NB!

Failure to descale the appliance as

described above voids the guarantee.

1. Press the P button to enter the menu;

2. Turn the selection knob until "Descaling" is

displayed;

3. Select by pressing the button. The

message "Descaling Confirm?" is displayed.

Press to activate the function.

4. If the message "INSERT WATER SPOUT" is

displayed, insert it (fig. 3).

5. The message "Insert Descaler. Confirm?" is

displayed.

6. Empty the water tank (A7).

7. Pour the descaler diluted with water (respect-

ing the proportions indicated on the descaler

bottle) into the water tank. Always use

descaler recommended by De’Longhi (contact

an authorized customer service center).

8. Place an empty container with a minimum

capacity of 50 oz under the hot water spout

(B7) (fig. 3).

Important!

Danger of burns Hot water con-

taining acid runs out of the hot water spout. Avoid

contact with splashes of water.

9. Press the button to confirm that you

have added the solution and begin the descal-

ing procedure.

10. The message "Descaling Underway" is dis-

played.

After about 30 minutes, the message "Rinsing

FILL TANK!" is displayed.

11. Remove the water tank, empty, rinse with run-

ning water, fill with clean water and replace.

12. Empty the container used to collect the

descaler solution and replace it under the hot

water spout.

13. Press the button to start rinsing. Hot

water runs out of the spout and the message

"Rinsing..." is displayed.

14. When the water tank is completely empty, the

message "Rinsing Complete... Confirm?" is

displayed.

15. Press the button, fill the water tank

and the appliance is ready for use.

SETTING WATER HARDNESS

The DESCALE message is displayed after a period

of time established according to water hardness.

The machine is factory set for a hardness value of

The machine can also be programmed according

to the hardness of your tap water. By program-

ming the water hardness, the machine will adjust

the frequency of the descaling message displayed.

Measuring water hardness

1. Remove the "TOTAL HARDNESS TEST" indica-

tor paper from its pack.

2. Immerse the paper completely in a glass of

water for one second.

3. Remove the paper from the water and shake

lightly.

Level 1

Level 2

Level 3

Level 4

Hole

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeLonghi ESAM 5500 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeLonghi ESAM 5500

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info