Bedienungsanleitung DeLonghi HBP742T (Seite 4 von 28) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

465835

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

ELECTRICAL CONNECTION

- Before plugging in the heater, check that the voltage of your domestic supply corresponds

to the voltage (V) indicated on the appliance.

- Check that the electrical socket has a rating of 10/16 Amps.

- THIS APPLIANCE CONFORMS TO DIRECTIVE EN 55014 GOVERNING RADIO INTERFE-

RENCE.

INSTALLATION

- Fix bracket to wall, complying with minimum measurement specified in fig. 1.

- Remove appliance from stand, by first turning black locking screw on top of stand 1/4

turn.

- Mount appliance on bracket and lock into place by turning black screw on top of bracket

(1/4 turn).

- Should appliance be installed in a bathroom, it must be mounted on the wall outside the

“safety area”, as shown in fig. 2.

- Only use appliance when fixed to a wall or mounted on its stand.

SWITCHING ON AND OFF PROCEDURE

To switch on appliance, whatever the function desired, put timer lever to position for conti-

nuous operation, or to position for “programmed” operation (see Timer section).

To switch off appliance, put timer lever to “0”.

SELECTOR KNOB

- Position A: Setting for hair dryer function

- Position B: Setting for hair dryer function + Heating at 1000 W without thermostat

- Position C: Heating at 1000 W without thermostat

- Position D: Heating at 2000 W with thermostat on maximum

- Position E: Anti-freeze function (appliance maintains room temperature at about 5°C, pre-

venting freezing with minimum energy consumption).

THERMOSTAT REGULATION

To regulate room temperature, proceed as follows:

- Put selector knob to position D;

- Wait for room temperature to reach comfort level desired, then slowly rotate selector knob

clockwise until warning light goes off.

The temperature thus set will be automatically maintained by the thermostat. Should further

temperature adjustment changes be required, turn knob clockwise to lower the temperature

and counter clockwise to raise it.

TIMER

For programmed function, appliance must be constantly connected to power supply.

For “programmed” heating, proceed as follows:

- For example, if time is 6 p.m., turn numbered dial of timer clockwise until number 18 is

aligned with pointer ▲ on timer.

- Set desired operating times by pushing inwards red teeth (fig. 4).

- Put timer lever to position . Appliance is now programmed to function automatically.

- To change programmed operating times, just push teeth back to original position and

reset timer for new functioning period.

- For use of appliance, outside preset timer programme, just put timer lever to position .

HAIR DRYER

Put timer lever to and selector knob to position A (also B = dual function).

Hair dryer works at 500 W with switch on handle set on position I; at 1000 W on position

II .

HBP 20-06-2000 15:43 Pagina 4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeLonghi HBP742T Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info