Bedienungsanleitung DeLonghi HCS2550 FTS (Seite 6 von 36) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

465724

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

1. ELECTRICAL CONNECTIONS

- Before plugging into the mains, make sure the voltage of your mains supply corresponds to the

V value indicated on the appliance and that the socket and power line are appropriate for the

load required.

- THIS APPLIANCE COMPLIES WITH DIRECTIVE 2004/108/EEC ON RADIO INTERFERENCE

SUPPRESSION.

2. Attaching the feet

To fit the feet, proceed as follows: Insert the foot into the guide on the side and push as far as it will

go until the two teeth hook in place (fig. 1).

3. Wall mounting

IMPORTANT: before drilling the wall, make sure the area is free of electrical wires or pipes. To fix

your convector heater to the wall, use the brackets “E” and “F” provided and appropriate screws and

anchors (provided).

Proceed as follows:

• Fix the brackets “E”, making sure the distances are as shown in fig. 3.

• Hang the heater on the two brackets fixed to the wall. Insert the two brackets “F” in the back of

the convector base as shown in fig. 4.

Mark the bracket fixing points on the wall. (When mounted, block the base of the heater in a fixed

position to prevent it being removed).

• Remove the heater, drill the wall and insert the anchors.

• Fix the heater again, inserting the brackets “F” into the base of the heater and fixing them to the

holes in the wall using the screws.

Now your heater is mounted on the wall.

The appliance must not be positioned directly underneath a fixed power point.

Position the appliance in such a way that the plug is easily accessible even after installation.

4. Operation and use

Turning on

Plug into the mains, turn the thermostat dial (B) to maximum and turn the appliance on by means of

the power selector (A) (fig.2) as described below:

• Turn the power selector knob (A) to the Min position to select minimum power (the Min power light comes

on).

• Turn the power selector knob (A) to the Med position to select medium power (the Med power light comes

on).

• Turn the power selector knob (A) to the Max position to select maximum power (the Max power

light comes on). In the fan version, both Min and Med lights come on.

5. Adjusting the thermostat

When the room has reached the required temperature, turn the thermostat dial (B) slowly anticlock-

wise until the lights go out and no further. The thermostat will automatically regulate the temperatu-

re set and keep it constant.

In spring or autumn or on mild days, you can save energy by using minimum power.

6. Frost prevention mode

With the thermostat dial in the position and one of the power levels selected, the appliance main-

tains room temperature at about 5°C, preventing freezing with minimal energy consumption.

7. Models with fan

A number of models have two fans for faster more even heating. To use this function, turn the power

selector (A) to the Max position (the corresponding light comes on).

8. Models with 24 hour timer (C)

To operate the appliance without the timer, place the timer pointer in the I position. To operate the

appliance at set times, position the pointer (D) in the position and proceed as follows:

• To operate the appliance without the timer, place the timer pointer in the I position. To operate the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeLonghi HCS2550 FTS Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info