Bedienungsanleitung Denon AVC-A1HDA (Seite 73 von 117) (Englisch)

616171

Zoom out

Zoom in

Vorherige Seite

1/117

Nächste Seite



Getting Started Connections Setup Playback Multi-Zone Information Troubleshooting

MODE SELECTOR

Remote ID

AMP (MAIN) iPod

NET/DTU

(Net Audio)

(Default)

81001 72815 62865

2 82001 72816 62837

3 83001 72817 62838

4 84001 72818 62839

Setting the Remote ID

When using multiple DENON AV receivers in the same room,

make this setting so that only the desired AV receiver operates.

Press [AMP] to set the main remote control unit to the

AMP mode.

Press and hold in [RC SETUP] for at least 3 seconds.

The signal transmission indicator ﬂashes twice.

Refer to the table at the right, and use [NUMBER] to

input the 5-digit number corresponding to the remote

ID to be changed.

The signal transmission indicator ﬂashes twice.

Press [iPod] or [NET/DTU] to select the mode to be

set.

Repeat steps 2 to 4 to set the remote IDs for all modes.

NOTE

• When changing a setting, be sure to set the same remote ID as the

AVP-A1HD’s (vpage 40).

• When changing the AMP mode’s remote ID, also change the “iPod”

and “NET/DTU” remote ID at the same time.

Point the main remote control units directly at each

other and press and hold the button on the other

device’s remote control unit that you want to learn.

Once learning is completed normally, the display lights and the

signal transmission indicator ﬂashes twice.

b If you want to learn other buttons, repeat steps 4 and 5.

b The mode can be switched by pressing [MODE SELECTOR].

b The signal transmission indicator lights once for a long time if

learning was not possible

Press and hold in [RC SETUP] for at least 3 seconds.

The signal transmission indicator ﬂashes twice and the setting

is completed.

[NUMBER]

[MODE SELECTOR]

[RC SETUP]

[ NET/DTU]

[ AMP]

[ iPod]

Other device’s

remote control unit

AVP-A1HD’s main remote

control unit (RC-1067)

Learning Function

If your AV devices are of a brand other than DENON or if they

cannot be operated with the preset memory function, their

remote control signals can be transfered to stored in the AVP-

A1HD’s main remote control unit.

Press [MODE SELECTOR] for the device you want to

set.

Press and hold in [RC SETUP] for at least 3 seconds.

The signal transmission indicator ﬂashes twice.

Press [9], [7] and [5], in that order.

The signal transmission indicator ﬂashes twice and the learning

mode is set.

Press the button to be set.

The main remote control unit’s display turns off.

b If a button that cannot be learned is pressed, the signal transmission

indicator lights but the signal is not learned.

• With some remote control units, the signals cannot be learned or the

device will not operate properly even when the signals have been

learned. In this case, use the device’s own remote control unit.

• Learned buttons have priority over the preset memory. If you no

longer need the learned setting, reset the learning function (vpage

71).

NOTE

• [HOME] cannot be learned.

• Do not learn any remote control signals at [RC SETUP].

• The AMP, ZONE2, ZONE3, ZONE4 and SYSTEM CALL modes cannot

be learned.

Signal transmission

indicator

Remote Control

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon AVC-A1HDA Seite 73

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info