Bedienungsanleitung Denon AVP-A1HDCI (Seite 75 von 124) (Englisch)

571793

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

Set the input source, input mode, surround mode,

room EQ settings and volume to the conditions you

want to store.

Press and hold the desired QUICK SELECT.

Keep pressing the button until the quick select indicator lights.

• To call out the settings, press QUICK SELECT at which the desired

settings were stored.

• The Quick Select name can be changed (vpage 40).

NOTE

Input sources stored with the quick select function cannot be selected

if they have been deleted at GUI menu “Manual Setup” – “Option

Setup” – “Source Delete” (vpage 40). In this case, store them

again.

Input Source Volume

Quick Select 1 DVD –40 dB

Quick Select 2 TV/CBL –40 dB

Quick Select 3 VCR –40 dB

[Quick Select Defaults]

Press CH SELECT.

Press ui or CH SELECT to select “Fader”.

Use o p to adjust the volume of the speakers.

(o: front, p: rear)

• The fader function does not affect the subwoofer.

• The fader can be adjusted until the volume of the speaker adjusted

to the lowest value is –12 dB.

Press CH SELECT.

Use ui or CH SELECT to select the speaker.

The speaker that can be set switches each time one of the

buttons is pressed.

Use o p to adjust the volume.

b ”OFF” can be set by pressing o when the subwoofer’s volume

is set to –12dB.

Turn off the power using <POWER>.

Press <POWER> while simultaneously pressing

<STANDARD> and <HOME THX CINEMA>.

Once the display starts ashing at intervals of about 1

second, release the two buttons.

If in step 3 the display does not ﬂash at intervals of about 1 second,

start over from step 1.

The surround parameters, tone control, room EQ settings and the

volumes of the different speakers are stored for the individual surround

modes.

Quick Select Function

With this function, the currently playing input source, input mode,

surround mode, room EQ settings and volume can be stored in

the memory.

Fader Function

This function lets you adjust (fade) the sound from all the front or

rear speakers at once.

Channel Level

You can adjust the channel level either according to the playback

sources or to suit your taste, as described below.

Resetting the Microprocessor

Perform this procedure if the display is abnormal or if operations

cannot be performed.

All settings are reset when the microcomputer is reset.

Personal Memory Plus Function

This function sets the settings (input mode, surround mode,

HDMI output mode, Picture Adjust, Audio Delay etc.) last selected

for the individual input sources.

When you switch to an input source, the settings are automatically

set to the ones that were set the last time that input source was

used.

Last Function Memory

This stores the settings as they were directly before the standby

mode was set.

When the power is turned back on, the settings are restored to as

they were directly before the standby mode was set.

Backup Memory

The various settings are backed up for about 1 week, even if the

power is turned off or the power cord is disconnected.



Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting

AVPA1HDCIEU_0121.indd 75 2008/01/21 12:50:03

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon AVP-A1HDCI Seite 75

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Denon AVP-A1HDCI

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info