Bedienungsanleitung Denon AVP-A1HDCI (Seite 13 von 128) (Spanisch)

571793

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

0

Getting Started Setup Playback Remote Control Multi-Zone Information Troubleshooting Speciﬁcations

The illustration below shows a basic example of installation of the ampliﬁer combined with 8 speakers and

a monitor.

Speaker Layout

Subwoofer Center speaker

Surround speakers

Front speakers

Place the front speakers to the

sides of the monitor or screen and

as ﬂush with the screen surface as

possible.

Surround back speakers

The table below shows a typical speaker conﬁguration for the AVP-A1HDCI.

FRONT

CENTER

SURROUND

SURROUND BACK

SUBWOOFER

(b)

L R L R L R L R 1 only

9.1-channels

S S S S S S S S S

–

7.1-channels

S S S S S

– –

S S

–

6.1-channels

S S S S S

– – – –

S S

5.1-channels

S S S S S

– – – – –

3.1-channels

S S S

– – – – – – –

2.1-channels

S S

– – – – – – – –

2-channels

S S

– – – – – – – – –

Two surround back speakers are required to use the THX Ultra2 Cinema,THX Music mode and THX Games

mode.

Set the surround back speakers so that the distance to the listening position is the same for both the left

and right speakers. It is also recommended that the deviations of the distance from the listening position

to L and R channel speakers (front left (FL) and front right (FR), surround left (SL) and surround right (SR),

surround back left (SBL) and surround back right (SBR)) is less than 2 ft (60 cm).

b The AVP-A1HDCI can be connected to a maximum of 3 subwoofers.

• For instructions for connecting speakers, please refer to the POA-A1HDCI owner’s manual.

• When using just one surround back speaker, connect it to the left channel (SBL).

• Connect the AVP-A1HDCI pre-out terminal to the power amp (sold separately).

• AVP-A1HDCI has a RCA pre-out terminal and XLR pre-out terminal. Connect accordingly with the power

amp you want to use.

• The polarity of the XLR pre-out terminal can be switched using GUI menu “Manual Setup” – “Option

Setup” – “XLR Out Polarity” (vpage 41).

• Connect the speakers to the power amp.

• Refer to the owner’s manual of each piece of equipment when making connections.

POA-A1HDCI Connection and Operation

• When connecting the AVP-A1HDCI to the power amp POA-A1HDCI with a control link cable (included

with the POA-A1HDCI), you can perform the following control operations.

•

POA-A1HDCI channel input selection and power amp settings

•

Link POA-A1HDCI to AVP-A1HDCI On/Standby control

•

Link POA-A1HDCI meter operation to AVP-A1HDCI display on/off control (vpage 43)

•

Updating POA-A1HDCI ﬁrmware (vpage 43)

• Up to 2 POA-A1HDCI units can be connected. Refer to the POA-A1HDCI owner's manual for making

connections and POA-A1HDCI settings.

Connecting to the Power Amp

Connections

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon AVP-A1HDCI Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Denon AVP-A1HDCI

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info