Bedienungsanleitung Denon AVP-A1HDCI (Seite 46 von 128) (Spanisch)

571793

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite



Getting Started Connections Playback Remote Control Multi-Zone Information Troubleshooting Speciﬁcations

A4 Remote ID

Set remote control ID.

Match the ID setting of the remote control unit and the receiver.

• When changing the remote ID, also change the AMP, iPod, TU and

NET/DTU modes of the main remote control unit at the same time

(vpage 80).

• When changing the remote ID, also change the sub remote control

unit at the same time (vpage 85).

A3 Digital Out

Set usage of OPT4 OUT.

NOTE

The ZONE4 operations cannot be performed when set to “Rec

Select”.

[Selectable items]

ZONE4 Select

Rec Select

[Selectable items]

A5 2Way Remote

Set when using the 2-way remote control unit.

When using a 2-way remote control unit (RC-7000CI and RC-7001RCI,

sold separately), set this to “Used”.

[Selectable items]

Used

Not Used

NOTE

• When using the 2-way remote control unit, connect to the Port 1

RS-232C connector.

• If GUI menu “Manual Setup” – “Option Setup” – “2Way Remote”is

set to “Used”, you cannot use port 1 of the RS-232C terminal for the

external controller.

A6 Dimmer

Adjust display brightness of the receiver.

Operating from the main unit

Press the DIMMER button.

[Selectable items]

Bright

Dim

Dark

OFF

Bright Dim

DarkOFF

A7 Setup Lock

Protect settings from inadvertent change.

• When “Setup Lock” is set to “ON”, the settings listed below can

no longer be changed. Also, “SETUP LOCKED!” is displayed if you

attempt to operate related buttons.

⋅ GUI menu operations

⋅ RESTORER

⋅ Night Mode

⋅ Parameter

⋅ Room EQ

⋅ Channel Level

⋅ Audio Delay

• To cancel the setting, press the MENU button to re-display the

“Setup Lock” screen, then change the setting to “OFF”.

[Selectable items]

OFF

A8 Maintenance Mode

This sets the function for maintenance by a DENON serviceperson

or installer. (For professional use only.)

NOTE

Only use this function if so instructed by a DENON serviceperson or

installer.

This function allows a DENON serviceperson or installer to check the

AVP-A1HDCI’s status and make settings via the Internet.

A9 Firmware Update

Update the ﬁrmware of the receiver.

Check for Update

You can check for ﬁrmware updates. You can also check approximately

how long it will take to complete an update.

Start

Execute the update process.

When updating starts, the power indicator becomes red and the GUI

screen is shut down.

The amount of update time which has elapsed is displayed during the

update process.

When updating is complete the power indicator becomes green and

normal status is resumed.

If the display reads as shown below, check the settings and network

environment, then update again.

Display Description

Updating failed Updating failed.

Server is busy Server is busy. Wait a while then try again.

Connection fail Failure connecting to server.

If POA-A1HDCI is connected using the control link, POA-A1HDCI

meter operation is turned OFF when the AVP-A1HDCI display is

turned “OFF”.

If POA-A1HDCI is connected using the control link, POA-A1HDCI is

updated simultaneously with update of AVP-A1HDCI.

Setup

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon AVP-A1HDCI Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Denon AVP-A1HDCI

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info