Bedienungsanleitung Denon AVR-1082 (Seite 12 von 82) (Englisch)

583778

Zoom out

Zoom in

Vorherige Seite

1/82

Nächste Seite

ENGLISH

NOTES:

— Assignment of low frequency signal range —

• The only signals produced from the subwoofer channel are LFE signals (during playback of Dolby Digital or

DTS signals) and the low frequency signal range of channels set to “Small” in the setup menu. The low

frequency signal range of channels set to “Large” are produced from those channels.

— Crossover Frequency —

• When “Subwoofer” is set to “Yes” at the “Speaker Configuration Setting”, set the frequency (Hz) below

which the bass sound of the various speakers is to be output from the subwoofer (the crossover

frequency).

• For speakers set to “Small”, sound with a frequency below the crossover frequency is cut, and the cut bass

sound is output from the subwoofer instead.

NOTE: For ordinary speaker systems, we recommend setting the crossover frequency to 80 Hz. When

using small speakers, however, setting the crossover frequency to a high frequency may improve

frequency response for frequencies near the crossover frequency.

— Subwoofer mode —

• The subwoofer mode setting is only valid when “Large” is set for the front speakers and “Ye s” is set for

the subwoofer in the “Speaker Configuration” settings (see page 10).

• When the “LFE+MAIN” playback mode is selected, the low frequency signal range of channels set to

“Large” are produced simultaneously from those channels and the subwoofer channel.

In this playback mode, the low frequency range expand more uniformly through the room, but depending

on the size and shape of the room, interference may result in a decrease of the actual volume of the low

frequency range.

• Selection of the “LFE ” play mode will play the low frequency signal range of the channel selected with

“Large” from that channel only. Therefore, the low frequency signal range that are played from the

subwoofer channel are only the low frequency signal range of LFE (only during Dolby Digital or DTS signal

playback) and the channel specified as “Small” in the setup menu.

• Select the play mode that provides bass reproduction with body.

• When the subwoofer is set to “Ye s”, bass sound is output from the subwoofer regardless of the subwoofer

mode setting in surround modes other than Dolby/DTS.

Set the operation for the digital signals when playing in the 6.1 SURROUND and DTS-ES surround modes.

Setting the SB CH Auto Flag Detect

At the System Setup Menu select “SB CH

Auto Flag Deterct” and press the ENTER

button.

BAND MODE

TUNING

ENTER

SHIFT

Setting

q Auto Flag Detect Mode (AFDM)

ON: This function only works for sources containing DTS-ES or 6.1-channel surround identification signals.

When this function is used, sources that have been recorded in 6.1-channel surround or DTS-ES are

automatically played in the 6.1-channel surround mode using the surround back speaker(s). (Refer to

w for the method of playback of the surround back speaker in this case.)

OFF: Set this mode if you wish to play normal 5.1-channel sources or sources not containing the

identification signals described below in the 6.1-channel mode.

NOTES:

• The “SB CH Auto Flag Detect” setting screen is displayed when the surround back speaker is set to

“Large” or “Small” at “Speaker Configuration”.

• The surround back speakers can also be turned on and off using the “6.1/7.1 Surround” surround

parameter. (See page 29.)

Select the desired setting.

We recommend setting this

to “OFF”.

When set to “ON”, the

operation for software for

which no identification

signals are recorded is set.

BAND MODE

TUNING

Enter the setting.

The System Setup Menu reappears.

ENTER

SHIFT

• Input the distance between the listening position and the different speakers to set the delay time for the

surround mode.

• The delay time can be set separately for surround speakers A and B.

Setting the delay time

Preparations:

Measure the distances between the listening position and the speakers

(L1 to L5 on the diagram at the right).

L1: Distance between center speaker and listening position

L2: Distance between front speakers and listening position

L3: Distance between surround speakers and listening position

L4: Distance between surround back speakers and listening position

L5: Distance between subwoofer and listening position

Center FRFL

Subwoofer

Listening position

SBRSBL

At the System Setup Menu select “Delay Time”.

BAND MODE

TUNING

w Non-Flag Source SBch Output

MTRX ON: Sources are played using the surround back speaker(s). The surround back channel is played

with digital matrix processing.

NON-MTRX: Sources are played using the surround back speaker(s). The same signals as those of the

surround channel are output from the surround back speaker(s).

OFF: Sources are played without using the surround back speaker(s).

Switch to the Delay Time screen.

ENTER

SHIFT

Example: When “Meters” is selected

Select the desired unit, meters or feet.

Select (darken) the desired units, “Meters” or “Feet”.

BAND MODE

TUNING

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon AVR-1082 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info