Bedienungsanleitung Denon AVR-1082 (Seite 23 von 82) (Englisch)

583778

Zoom out

Zoom in

Vorherige Seite

1/82

Nächste Seite

ENGLISH

115

2 3

Playing the input source

456

789

+10

TV/

VCR

SKIP

ENTER

VOLUME

CHANNEL

TUNER

VDP

VCR-1

RDS PTY RT

VCR-2/ V.AUX

DVD

TV/DBS

CDR/TAPE

PHONO

SURROUND

INPUT

OUTPUT

TEST

TONE

SPEAKER

6.1 / 7.1

SURROUND

5CH / 7CH

ANALOG

EXT.INMODE

CALL 2

BACKLIGHT

CALL 1

STEREO

DOLBY/DTS

SURROUND

DSP

SIMU.

SYSTEM CALL

DIRECT

SHIFT

MUTING

BAND MODE

TUNING

Select the input source to be played.

Example: CD

To select the input source

when REC MULTI OUT or

TUNING PRESET is selected,

press the SOURCE button

then operate the input function

selector.

SOURCE

FUNCTION

(Main unit) (Remote control unit)

AUTO PCM DTS

• Selecting the external input (EXT. IN) mode

Press the EXT. IN (on the EXT. IN button on

the remote control unit) to switch the external

input.

EXT.IN

(Main unit) (Remote control unit)

• Selecting the AUTO, PCM and DTS modes

The mode switches as shown below each

time the INPUT MODE button is pressed.

MODE

(Remote control unit)

Input mode selection function

Different input modes can be selected for the different

input sources. The selected input modes for the separate

input sources are stored in the memory.

q AUTO (auto mode)

In this mode, the types of signals being input to the

digital and analog input jacks for the selected input

source are detected and the program in the AVR-

3802’s surround decoder is selected automatically

upon playback. This mode can be selected for all input

sources other than PHONO and TUNER.

The presence or absence of digital signals is detected,

the signals input to the digital input jacks are identified

and decoding and playback are performed

automatically in DTS, Dolby Digital or PCM (2 channel

stereo) format. If no digital signal is being input, the

analog input jacks are selected.

Use this mode to play Dolby Digital signals.

w PCM (exclusive PCM signal playback mode)

Decoding and playback are only performed when PCM

signals are being input.

Note that noise may be generated when using this

mode to play signals other than PCM signals.

e DTS (exclusive DTS signal playback mode)

Decoding and playback are only performed when DTS

signals are being input.

r ANALOG (exclusive analog audio signal playback

mode)

The signals input to the analog input jacks are decoded

and played.

t EXT. IN (external decoder input jack selection mode)

The signals being input to the external decoder input

jacks are played without passing through the surround

circuitry.

NOTE:

• Note that noise will be output when CDs or LDs

recorded in DTS format are played in the “PCM”

(exclusive PCM signal playback) or “ANALOG”

(exclusive PCM signal playback) mode. Select the

AUTO or DTS mode when playing signals recorded in

DTS from a laser disc player or CD player.

Note on playing a source encorded with DTS

• Noise may be generated at the beginning of

playback and while searching during DTS

playback in the AUTO mode. If so, play in the

DTS mode.

(Main unit)

Select the input mode.

• Selecting the analog mode

Press the ANALOG button to switch to the

analog input.

ANALOG

(Main unit) (Remote control unit)

• Selecting the AUTO mode

Press the AUTO button to switch to the auto

mode.

AUTO

(Main unit)

• Selecting the PCM mode

Press the PCM button to switch to the PCM

signal input.

PCM

(Main unit)

• Selecting the DTS mode

Press the DTS button to switch to the DTS

signal input.

DTS

(Main unit)

Select the play mode.

Example: Stereo

SURROUND

MODE

STEREO

(Main unit) (Remote control unit)

The volume can be adjusted within the range of

–70 to 0 to 18 dB, in steps of 1 dB. However, when

the channel level is set as described on page 13 or

page 27, if the volume for any channel is set at +1

dB or greater, the volume cannot be adjusted up to

18 dB. (In this case the maximum volume

adjustment range is “18 dB — (Maximum value of

channel level)”.)

Input mode when playing DTS sources

• Noise will be output if DTS-compatible CDs or LDs

are played in the “ANALOG” or “PCM” mode.

When playing DTS-compatible sources, be sure to

connect the source component to the digital input

jacks (OPTICAL/COAXIAL) and set the input mode to

“DTS”.

Start playback on the selected component.

• For operating instructions, refer to the

component’s manual.

Adjust the volume.

MASTER VOLUME

VOLUME

(Main unit) (Remote control unit)

The volume level is

displayed on the

master volume level

display.

SELECT

To select the surround mode

while adjusting the surround

parameters, channel volume or

tone control, press the

surround mode button then

operate the selector.

SURROUND

MODE

(Main unit)

Input mode display

ANALOGDIGITAL

DIGITAL

ANALOG

AUTO

INPUT

PCM DTS

AUTO

INPUT

PCM DTS

AUTO

INPUT

PCM DTS

AUTO

INPUT

PCM DTS

• In the AUTO mode

• In the DIGITAL PCM mode

• In the DIGITAL DTS mode

• In the ANALOG mode

One of these lights, depending on

the input signal.

Input signal display

SIGNAL

DIGITAL

SIGNAL

• DOLBY DIGITAL

• DTS

• PCM

The indicator lights when digital signals

are being input properly. If the indicator

does not light, check whether the digital input

component setup (page 14) and connections are

correct and whether the component’s power is

turned on.

DIGITAL

NOTE:

• The indicator will light when playing

CD-ROMs containing data other than audio

signals, but no sound will be heard.

DIGITAL

Denon AVR-1082 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info