Bedienungsanleitung Denon AVR-1613 (Seite 38 von 48) (Englisch)

583940

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

38 Maintenance

Checking and Cleaning the

Print Head

If your printouts are unexpectedly light, colors are

missing, or you see light or dark lines across the

page, you may need to clean the print head. This

clears the print head nozzles, which can become

clogged if you do not use the product for a long time.

Note:

Make sure the front tray is in the paper position (lower position)

and the CD/DVD tray is not inserted in the product (& page 8).

Tip:

We recommend that you turn on the product at least once a month

to maintain good print quality.

Checking the print head

You can print a nozzle check pattern to see if any

print head nozzles are clogged, or to check the results

after cleaning the print head.

1. Load A4-size plain paper (& page 8).

2. Press the F [Setup] button. (If you have just

finished cleaning the print head, you can start

the nozzle check by pressing the x Start button.)

3. Use the l or r button to select Maintenance,

then press OK.

4. Use the u or d button to select Nozzle Check,

then press OK.

5. Press the x Start button.

6. Examine the nozzle check pattern you printed.

Each staggered line should be solid, with no

gaps, as shown.

■ If your printout looks okay, the print head

does not need to be cleaned yet. Press OK to

return to the main menu.

■ If you see any gaps, as shown below, clean

the print head as described in the next

section.

Cleaning the print head

Follow these steps to clean the print head so it can

deliver ink properly. Before cleaning the print head,

run a nozzle check to see if the print head needs

cleaning (& “Checking the print head” on page 38).

Note:

❏ Print head cleaning uses ink, so clean it only if quality declines.

❏ If a message on the LCD screen tells you that a cartridge is

expended or low on ink, you cannot clean the print head. You

must first replace the indicated ink cartridge (& “Replacing Ink

Cartridges” on page 35).

1. Make sure the product is turned on but not

printing.

2. Press the F [Setup] button.

3. Use the l or r button to select Maintenance,

then press OK.

4. Use the u or d button to select Head Cleaning,

then press OK.

5. Press the x Start button to start cleaning the

print head.

The product begins cleaning the print head and

the Print head cleaning in progress. Please

wait. message appears on the LCD screen.

c Caution:

Never turn off the product while head cleaning is in progress.

You may damage it.

6. When cleaning finishes, a message displays on

the LCD screen. Then press the x Start button to

print a nozzle check pattern to check the results

(& “Checking the print head” on page 38).

If there are still gaps or the test patterns are faint,

run another cleaning cycle and check the nozzles

again.

Note:

If you do not see any improvement after cleaning about four

times, turn off the product and wait for at least 6 hours. This

lets any dried ink soften. Then try cleaning the print head

again. If quality still does not improve, one of the ink

cartridges may be old or damaged and needs to be replaced

(& “Replacing Ink Cartridges” on page 35).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon AVR-1613 Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Denon AVR-1613

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info