ENGLISH
34
Symptom Cause Measures Page
Remote control unit
This unit does not operate
properly when remote control
unit is used.
•
Batteries dead.
•
Remote control unit too far from
this unit.
•
Obstacle between this unit and
remote control unit.
•
Different button is being pressed.
•
< and > ends of battery inserted in
reverse.
•
Replace with new batteries.
•
Move closer.
•
Remove obstacle.
•
Press the proper button.
•
Insert batteries properly.
9
9
9
—
9
NOTE:
When a subwoofer has been connected and the virtual surround function is being used, the signal played from
the subwoofer channel is LFE only (only when playing Dolby Digital or DTS signals) for initial factory settings
(i.e., the setting of the front speaker is “LARGE” and the setting of the subwoofer mode is “NORM”).
When subwoofer effects are felt to be weak, try setting the subwoofer mode to “+MAIN”, or the front
speaker to “SMALL” in the System setup ”Speaker Configuration” settings.
Making these settings will result in the low-frequency sounds of the front channel being played from the
subwoofer.
2 Audio section
• Power amplifier
Rated output: Front: 80 W + 80 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.)
110 W + 110 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)
Center: 80 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.)
110 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)
Surround: 80 W + 80 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.)
110 W + 110 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)
Surround Back:
80 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.)
110 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)
Dynamic power: 100 W x 2 ch (8 Ω/ohms)
145 W x 2 ch (4 Ω/ohms)
170 W x 2 ch (2 Ω/ohms)
Output terminals: Front/Center/Surround: 16 to 16 Ω/ohms
Surround Back: A or B 16 to 16 Ω/ohms
A + B 12 to 16 Ω/ohms
• Analog
LINE input - PRE OUT
Input sensitivity/input impedance: 200 mV/47 kΩ/kohms
Frequency response: 10 Hz ~ 100 kHz: +1, –3 dB (DIRECT mode)
S/N ratio: 100 dB (IHF-A weighted) (DIRECT mode)
Distortion: 0.008% (20 Hz ~ 20 kHz) (DIRECT mode)
Rated output: 1.2 V
• Phono equalizer (PHONO input — REC OUT)
Input sensitivity: 2.5 mV
RIAA deviation: ±1 dB (20 Hz to 20 kHz)
Signal-to-noise ratio: 74 dB (A weighting, with 5 mV input)
Rated output / Maximum output: 150 mV / 7 V
Distortion factor: 0.03% (1 kHz, 3 V)
20
SPECIFICATIONS
2 Video section
• Standard video jacks
Input/output level and impedance: 1 V p-p, 75 Ω/ohms
Frequency response: 5 Hz ~ 10 MHz — +1, –3 dB
• S-video jacks
Input/output level and impedance: Y (brightness) signal — 1 Vp-p, 75 Ω/ohms
C (color) signal — 0.286 Vp-p, 75 Ω/ohms
Frequency response: 5 Hz ~ 10 MHz — +1, –3 dB
• Color component video terminal
Input / output level and impedance: Y (brightness) signal — 1 Vp-p, 75 Ω/ohms
P
B/C
B (blue) signal — 0.7 Vp-p, 75 Ω/ohms
P
R/CR (red) signal — 0.7Vp-p, 75 Ω/ohms
Frequency response: 5 Hz ~ 27 MHz — +1, –3 dB
2 Tuner section
[FM] (note:
µ
V at 75
Ω
/ohms, 0 dBf = 1 x 10
–15
W) [AM]
Receiving range: 87.50 MHz ~ 108.00 MHz 522 kHz ~ 1611 kHz
Usable sensitivity: 1.0 µV (11.2 dBf) 18 µV
50 dB quieting sensitivity: MONO 1.6
µ
V (15.3 dBf)
STEREO 23
µ
V (38.5 dBf)
S/N ratio: MONO 80 dB (IHF-A weighted)
STEREO 75 dB (IHF-A weighted)
Total harmonic distortion: MONO 0.15 % (1 kHz)
STEREO 0.3 % (1 kHz)
2 General
Power supply: AC 230 V, 50 Hz
Power consumption: 260 W
1 W Max. (Standby)
Maximum external dimensions: 434 (W) x 171 (H) x 417 (D) mm
Mass: 11.7 kg
2 Remote control unit (RC-917)
Batteries: R6P/AA Type (two batteries)
External dimensions: 55 (W) x 225 (H) x 34.5 (D) mm
Mass: 165 g (including batteries)
For purposes of improvement, specifications and design are subject to change without notice.
