Bedienungsanleitung Denon AVR-1909 (Seite 29 von 81) (Englisch)

60741

Zoom out

Zoom in

Vorherige Seite

1/81

Nächste Seite

Getting Started Connections Setup Playback Remote Control Multi-zone Information Troubleshooting

ENGLISH

Subwoofer Setup

Select low range signal to be reproduced by subwoofer.

• This can be set when menu “Speaker Conﬁguration” – “Subwoofer”

is set to “Yes”.

• Play music or a movie source and select the mode offering the

strongest bass.

• Select “LFE+Main” if you want the bass signals to always be

produced from the subwoofer.

[Selectable items]

LFE

: Play low range and LFE signal of channels set to

“Small”.

LFE+Main

: Play low range and LFE signal of all channels.

Distance

Set distance from listening position to speakers.

Before making the settings, measure the distance from the

listening position to the different speakers.

Unit

Select unit for distance.

[Selectable items]

Meters

Feet

Step

Select step. (smallest distance)

[Selectable items]

0.1m

0.01m

: Can be selected when “Meters” is set.

1ft

0.1ft

: Can be selected when “Feet” is set.

Default

Reset the settings to the default values.

Distance measurement

Select the speaker you want to set, then set the distance.

Set the value closest to the measured distance.

[Variable range]

0.00m ~ 18.00m

: Display when “Meters” is set.

0.0ft ~ 60.0ft

: Display when “Feet” is set.

NOTE

Set the distance between the listening position and the various

speakers to no more than 6.00 meters (20.0 ft).

For details on how to select, set and cancel settings for each menu, see “Menu Operations” (vpage 17).



• When the menu “Speaker Conﬁguration” – “Surround Back

Speaker” setting (vpage 24) is set to “1spkr”, the surround back

speaker display is set to “SB”.

• Speakers set to “None” in the “Speaker Conﬁguration” settings are

not displayed.

• When “Channel Level” is adjusted, the adjusted values are set for all

the surround modes. To adjust the channel level separately for the

different surround modes, use the operation see page 54.

Operating from the remote control unit

Adjusting with the remote control unit using the test tones is only

possible in the “Auto” mode and only effective in the STANDARD

mode. The adjusted levels for the different modes are automatically

stored in the memory.

GAdjusting using test tonesH

q Press [TEST].

Test tones are output from the various speakers.

w Use o p to adjust so that the volume is equal for all speakers.

e When the adjustments are completed, press [TEST] again.

Test Tone

Select test tone playback method.

[Selectable items]

Auto

: Automatically switch speaker from which test tone is

output.

Manual

: Manually switch speaker from which test tone is output.

Channel Level

Adjust channel levels to obtain equal volume from all speakers.

Test Tone Start

Output test tone.

[Variable range]

OFF

–12dB

0dB

+12dB

z In the case of a subwoofer, reducing the volume when it is at

“–12dB” will change the setting to “OFF” (none).

Default

Reset the settings to the default values.

Speciﬁcations

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon AVR-1909 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Denon AVR-1909

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info