Bedienungsanleitung Denon AVR-2309CI (Seite 19 von 82) (Englisch)

584054

Zoom out

Zoom in

Vorherige Seite

1/82

Nächste Seite



Getting Started Connections Setup Playback Remote Control Multi-zone Information Troubleshooting

ENGLISH

Speciﬁcations

External Controller

• When using in combination with an RF Remote Controller (RC-

7000CI, sold separately) or RF Remote Receiver (RC-7001RCI, sold

separately) two-way communication with an RF Remote Controller

is possible.

The AVR-2309CI’s status information as well as iPod can be browsed

watching the RF Remote Controller’s display. For details, refer to the

operating instructions of the respective devices.

• When used in combination with an RF Remote Controller or RF

Remote Receiver, make the settings at menu “Manual Setup”

– “Option Setup” – “232C Port” – “2Way Remote” (vpage 30).

• On the menu, when setting “Manual Setup” – “Option Setup” –

“232C Port” to “2Way Remote”, you cannot use the RS-232C port

as an external controller (vpage 30).

RS-232C connector

This connector is used for an external

controller.

b If you wish to control the AVR-2309CI from

an external controller using the RS-232C

connector, perform the operation below

beforehand.

q Turn on the AVR-2309CI’s power.

w Turn off the AVR-2309CI’s power from the

external controller.

e Check that the AVR-2309CI is in the standby

mode.

Trigger output jack

The power of an external device equipped with a trigger input jack

can be turned on and off in association with operations on the AVR-

2309CI. For details, see menu “Manual Setup” – “Option Setup”

– “Trigger Out” (vpage 30).

• Output: DC 12 V 150 mA MAX.

Check the trigger input conditions of the connected device.

Connections

Multi-zone

ZONE2 out Connections

If another pre-main (integrated) ampliﬁer is connected, the ZONE2 out

connectors can be used to play a different program source in ZONE2

at the same time (vpage 61 ~ 63).

"6%*0

"69

065

Pre-main amplier

(ZONE2)

Input Output

Infrared

retransmitter

Infrared

sensor

Extension jack for future use.

(Connect devices corresponding

with room to room function to

this jack. )

NOTE

• For the audio output, use high quality pin-plug cords so that no

induction humming or noise is produced.

• For instructions on installing and operating separately sold devices,

refer to the respective devices’ operating instructions.

• To conduct multi-zone playback, see “Amp Assign / Multi-zone

Connections and Operations” (vpage 61 ~ 63).

NOTE

• Insert the AC plugs securely. Incomplete connections could cause

noise.

• Only use the AC outlets to plug in audio equipment. Do not use

them as power supplies for hairdryers or anything other than audio

equipment.

Wait until all connections have been completed before connecting the

power cord.

To household

power outlet

(AC 120 V, 60 Hz)

Power cord

(supplied)

Connection to the AC outlets

• These outlets supply power to external audio

equipment.

• The power supplied from these outlets turns

on and off together with the set’s power

switch.

• Audio equipment with a total power

consumption of 120 W (1 A) can be

connected.

Connecting the Power Cord

Turning the Power On (vpage 47)

Once Connections are

Completed

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon AVR-2309CI Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Denon AVR-2309CI

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info