Bedienungsanleitung Denon AVR-2310CI (Seite 59 von 78) (Englisch)

584055

Zoom out

Zoom in

Vorherige Seite

1/78

Nächste Seite



ENGLISH

Getting Started Connections Playback Remote Control Information Troubleshooting SpeciﬁcationsSettings

Playing 2-Channel Sound in ZONE2 (Multizone Function)

2-channel sound can be played in rooms other than the MAIN

ZONE where multichannel sound is played.

There are two methods to do this, as described below. Choose

one of the methods.

q ZONE2 playback by speaker output

wZONE2 playback by audio output (PRE OUT) (using an

external amplifier))

q ZONE2 Playback by Speaker

Output

Preparations

Connecting and setting the speakers

Connecting the speakersn

w q w q

(L) (R)

Necessary settings

Set the AMP ASSIGN mode to “ZONE2”.

“Amp Assign” (vpage 28)

Perform the settings at “ZONE2 Setup”.

“Making the ZONE2 settings” (vpage 33)

•

w ZONE2 Playback by Audio

Output

Connection (ZONE2)

The audio signals connected to the AVR-2310CI’s ZONE2 output

terminals (ZONE2 OUT) are output to the ZONE2’s ampliﬁer and played

with that ampliﬁer.

"69

Adjust the volume on the connected ampliﬁer.

Also be sure to read the operating instructions of the connected

devices.

•

1Set the remote control unit’s

“device selector switches” as

shown on right.

2Turn on the AVR-2310CI’s power.

(vpage 20“Turning the Power On”)

3Press to turn on the ZONE2 power.

When the power turns on, the “ ” indicator lights on the

display.

b The power can be turned on by pressing the one of

while in the standby mode.

4Use the input source selector to choose the input

source.

The selected input source is shown on the display.

NOTE

When “SOURCE” is selected for the input source, the sound being

played in the MAIN ZONE is played. No sound is output if a digital

audio input source is being played in the MAIN ZONE.

Adjusting the volume (for “q ZONE2 playback by

speaker output”)

Use to adjust the volume.

GVariable rangeH – – – –80dB(1) ~ –40dB(41) ~ +18dB(99)

bThe volume can be adjusted up to the level set at “Vol. Limit”

(vpage 33).

bThe volume display is the display set at “Volume Display”

(vpage 33).

AVR-2310CI

The operation is the same for “q ZONE2 playback by speaker

output” and “w ZONE2 playback by audio output”.

Playback

MAIN ZONE

ZONE2

Rear

For “w ZONE2 playback by audio output”, adjust the volume on the

connected ampliﬁer.

NOTE

• We recommend using high quality pin-plug cables for audio

connections in order to prevent noise.

• It is not possible to play the digital audio signals input from the

HDMI, COAXIAL or OPTICAL terminals in ZONE2. Play using analog

connections (in stereo).

With the Amp Assign function, Zone 2 audio signals are output from

the AVR-2310CI's SURR BACK/AMP ASSIGN terminals.

Multi-Zone

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon AVR-2310CI Seite 59

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Denon AVR-2310CI

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info