Bedienungsanleitung Denon AVR-2312CI (Seite 144 von 152) (Englisch)

584187

144

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

141

GAudioH

Symptom Cause/Solution Page

Audio is not output. •Check the connections for all devices.

•Check the speaker connections and conﬁgurations.

•Check whether the audio device power is turned on.

•Adjust the master volume.

•Cancel the mute mode.

•Select a suitable input source.

•Select a suitable input mode.

•Disconnect the headphones. No sound is output from the

speakers when headphones are connected.

C3,8,

10,11,12,13,

14,15,16,17

C6,59,

60,61,62,

63,64

–

27, 80

26, 80

125

No sound is

produced from

surround speaker.

•Check if the surround speakers are connected to the SURROUND

terminals.

–

No sound is

produced from

surround back

speaker.

•Check if “Amp Assign” is set appropriately in order to output

audio from the surround back speakers.

•Set “Speaker Conﬁg.” – “Surr.Back” on the menu to something

other than “None”.

•Set “Surround Parameters” – “Surround Back” on the menu to

something other than “OFF”.

•Set the surround mode to something other than “STEREO” and

“VIRTUAL“.

102

103

No sound is

produced from front

height speaker.

•Set “Surround Parameters” – “PLgz Height” on the menu to

“ON”.

•Check if “Amp Assign” is set appropriately in order to output

audio from the front height speakers.

•Set “Speaker Conﬁg.” – “Front Height” on the menu to something

other than “None”.

102

103

No sound is

produced from

subwoofer.

•Check the subwoofer connections.

•Turn on the subwoofer’s power.

•Set “Speaker Conﬁg.” – “Subwoofer” on the menu to “Yes”.

•If “Front” and “Center” for “Speaker Conﬁg.” are set to “Large”,

and “Subwoofer Mode” is set to “LFE”, no sound may be output

from the subwoofers, depending on the input signal or selected

surround mode.

C6,59,

60,61,62,

63,64

–

102

102, 103

Symptom Cause/Solution Page

DTS sound is not

output.

•Set “Decode Mode” on the menu to “Auto” or “DTS”. 91

Dolby TrueHD, DTS-

HD, Dolby Digital

Plus audio is not

output.

•Make HDMI connections. 8

Dolby PLg mode or

DTS NEO:6 mode

cannot be selected.

•Check that “Speaker Conﬁg.” – “Center” or “Surround” is set

to other than “None”. If the speaker system is 2.0/2.1ch, this

surround mode cannot be selected.

•When headphones are used, Dolby PLg or DTS NEO:6 cannot be

selected.

102

–

Audyssey MultEQ®

XT, Audyssey

Dynamic EQ® and

Audyssey Dynamic

Volume® cannot be

selected.

•Switch the surround mode to other than “DIRECT” or “PURE

DIRECT”.

•When headphones are used, MultEQ® XT, Dynamic EQ® and

Dynamic Volume® cannot be selected.

–

Dynamic EQ® and

Dynamic Volume®

cannot be selected.

•Run Audyssey® Auto Setup. 19, 65

RESTORER cannot

be selected.

•Check that an analog signal or PCM signal (fs=44.1/48 kHz) is

input. For playback of multichannel signals such as Dolby Digital

or DTS surround, RESTORER cannot be used.

•Switch the surround mode to other than “DIRECT” or “PURE

DIRECT”.

Basic version

Advanced version

InformationInformation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon AVR-2312CI Seite 144

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Denon AVR-2312CI

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info