Bedienungsanleitung Denon AVR-2805 (Seite 13 von 121) (Deutsch)

498710

Zoom out

Zoom in

Vorherige Seite

1/121

Nächste Seite

ENGLISH

Before setting up the system

Display the System Setup Menu.

Check that all the connections are correct, then turn on the main unit’s power.

Setup will not be possible when the unit is set to Pure Direct ON or when the headphones are plugged

in. Therefore, please cancel the mode or reverse the condition.

Auto Set/RoomEQ

*System Setup

(Remote control unit)

NOTES:

• The System Setup menu composition is of a layered design that includes the related items below the large

table title as contained in the tables of Pages 11 and 12.

• Wherever your position in System Setup, one more press of the System Setup button permits a move to

one level higher.

Auto setup/Room EQ

The Auto Setup function of this unit performs an analysis of the speaker system and measures the acoustic

characteristics of your room to permit an appropriate automatic setting.

When performing Auto Setup, a microphone is required for the setup.

q Speaker Config.: This sets the speaker connection mode, polarity, and bass reproduction ability.

w Delay Time :

This sets the optimum delay time from each speaker corresponding to the listening position.

e Channel Level : This sets the volume that is output from each speaker.

r Room EQ : This sets the frequency response of each speaker.

2 Measurement and setting details

NOTE:

• A loud test tone is output during the measurement. Please consider this should you be planning nighttime

measurements, and consider not allowing small children into the listening room at this time.

MODE ANALOG EXT. IN

Connect the microphone for Auto Setup to the

Setup Mic connector on the front panel of the

unit.

Place the microphone for Auto Setup at the

actual listening position which will be at the

same height as your ears. Use a tripod or level

surface at positioning.

Connecting the microphone for Auto Setup

NOTE:

• When using other microphone. (See page 16)

Listening position

Select “Auto Setup / Room EQ” at the System Setup

Menu.

Display the Auto Setup / Room EQ menu.

Auto Set/RoomEQ

*System Setup

(Remote control unit)

Setting the Auto Setup / Room EQ

1-1 Setting the Auto Setup

Select “Auto Setup” at the Auto Setup / Room EQ

Menu.

Display the Auto Setup screen.

Check the “Power Amp Assign” setting.

• When “Surround Back” is selected, the test tone during Auto Setup will be output from the

Surround Back speaker.

• When “ZONE2” is selected, change the setting to ”ZONE2”. The test tone during Auto Setup is set

so that it will not be output to ZONE2 (Another room).

q Select the Power Amp Assign setting.

Auto Setup

*AutoSet/RoomEQ

P.Amp: SB

*Auto Setup

w Select “Surround Back” or “ZONE2”.

(Remote control unit)

NOTE:

• When “ZONE2” is selected at System

Setup Menu “Power Amp Assign”,

surround back speaker is not displayed as

the target of setup in “2-1. Speaker

Config.”. The results is reflected in “5-1.

Power Amp Assign”.

(Remote control unit)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon AVR-2805 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Denon AVR-2805

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info