Bedienungsanleitung Denon AVR-2808 (Seite 58 von 96) (Englisch)

65891

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite



Getting Started Connections Setup Playback Multi-Zone Information Troubleshooting

ENGLISH

MODE SELECTOR

Remote ID

AMP (MAIN)

TUNER

iPod

(Analog TUNER)

(Default)

81001 52863 72815

2 82001 52795 72816

3 83001 52800 72817

4 84001 52805 72818

Refer to the table at the below, and use [NUMBER] to

input the 5-digit number corresponding to the remote

ID to be changed.

The signal transmission indicator ﬂashes twice.

Press [TU] (

mode) or [iPod] to select the mode

to be set.

Repeat steps 2 to 4 to set the remote IDs for all

modes.

NOTE

• When changing a setting, be sure to set the same remote ID as the

AVR-2808’s (vpage 32).

• When changing the AMP mode’s remote ID, also change the

“TUNER” and “iPod” remote ID at the same time.

• Set the remote ID of an analog tuner for TUNER ( ).

[ AMP]

[NUMBER]

[MODE SELECTOR]

[RC SETUP]

[ TU]

[ iPod]

[POWER ON]

[CHANNEL +/–]

[SYSTEM CALL]

Press the button to be set.

The main remote control unit’s display turns off.

b If a button that cannot be learned is pressed, the signal transmission

indicator lights but the signal is not learned.

Point the main remote control units directly at each

other and press and hold the button on the other

device’s remote control unit that you want to learn.

Once learning is completed normally, the display lights and the

signal transmission indicator ﬂashes twice.

b If you want to learn other buttons, repeat steps 4 and 5.

b The mode can be switched by pressing [MODE SELECTOR].

b The signal transmission indicator lights once for a long time if

learning was not possible

Press and hold in [RC SETUP] for at least 3 seconds.

The signal transmission indicator ﬂashes twice and the setting

is completed.

• With some remote control units, the signals cannot be learned or the

device will not operate properly even when the signals have been

learned. In this case, use the device’s own remote control unit.

• Learned buttons have priority over the preset memory. If you no

longer need the learned setting, reset the learning function (vpage

56).

NOTE

• [HOME] cannot be learned.

• Do not learn any remote control signals at [RC SETUP].

• The AMP, ZONE2, ZONE3, ZONE4 and SYSTEM CALL modes cannot

be learned.

Signal transmission

indicator

Remote Control

[8], [9],

[6], [7],

[1], [3], [2]

[ TV]

Setting the Remote ID

When using multiple DENON AV receivers in the same room,

make this setting so that only the desired AV receiver operates.

Press [AMP] to set the main remote control unit to the

AMP mode.

Press and hold in [RC SETUP] for at least 3 seconds.

The signal transmission indicator ﬂashes twice.

Learning Function

If your AV devices are of a brand other than DENON or if they

cannot be operated with the preset memory function, their

remote control signals can be transfered to stored in the AVR-

2808’s main remote control unit.

Press [MODE SELECTOR] for the device you want to

set.

Press and hold in [RC SETUP] for at least 3 seconds.

The signal transmission indicator ﬂashes twice.

Press [9], [7] and [5], in that order.

The signal transmission indicator ﬂashes twice and the learning

mode is set.

Other device’s

remote control unit

AVR-2808’s main remote

control unit (RC-1068)

1.AVR2808E2_ENG.indd 58 2007/09/28 11:41:49

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon AVR-2808 Seite 58

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Denon AVR-2808

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info