Bedienungsanleitung Denon AVR-3313CI (Seite 176 von 187) (Englisch)

584353

176

Zoom out

Zoom in

Vorherige Seite

1/187

Nächste Seite

173

Symptom Cause/Solution Page

No sound is

produced from

subwoofer.

•Check the subwoofer connections.

•Turn on the subwoofer’s power.

•Set “Speaker Conﬁg.” – “Subwoofer” on the menu to “Yes”.

•If “Front” and “Center” for “Speaker Conﬁg.” are set to “Large”,

and “Subwoofer Mode” is set to “LFE”, no sound may be output

from the subwoofers, depending on the input signal or selected

sound mode.

85,86,87,88,

89,90,91

–

130

130, 131

DTS sound is not

output.

•Set “Decode Mode” on the menu to “Auto” or “DTS”. 127

Dolby TrueHD, DTS-

HD, Dolby Digital

Plus audio is not

output.

•Make HDMI connections. 11

Dolby PLg mode or

DTS NEO:6 mode

cannot be selected.

•Check that “Speaker Conﬁg.” – “Center” or “Surround” is set to

other than “None”. If the speaker system is 2.0/2.1ch, this sound

mode cannot be selected.

•When headphones are used, Dolby PLg or DTS NEO:6 cannot be

selected.

130

–

Audyssey MultEQ®

XT, Audyssey

Dynamic EQ® and

Audyssey Dynamic

Volume® cannot be

selected.

•Switch the sound mode to other than “DIRECT” or “PURE

DIRECT”.

•When headphones are used, Audyssey MultEQ® XT, Audyssey

Dynamic EQ® and Audyssey Dynamic Volume® cannot be

selected.

–

Audyssey DSX®

cannot be selected.

•Check that “Speaker Conﬁg.” – “Front Height” or “Front Wide” is

set to other than “None”.

•Check that “Speaker Conﬁg.” – “Center” is set to other than

“None”.

•Switch the sound mode to DOLBY listening mode or DTS listening

mode.

•When headphones are used, Audyssey DSX® cannot be selected.

131

130

–

Audyssey Dynamic

EQ® and Audyssey

Dynamic Volume®

cannot be selected.

•Run Audyssey® Setup. 29, 92

Symptom Cause/Solution Page

“Restorer” cannot

be selected.

•Check that an analog signal or PCM signal (Sample Rate=44.1/48

kHz) is input. For playback of multichannel signals such as Dolby

Digital or DTS surround, “Restorer” cannot be used.

•Switch the sound mode to other than “DIRECT” or “PURE

DIRECT”.

115

When the HDMI

ZONE2 function is

used, in spite of

“Assign Mode”

being set to

“ZONE2”, no audio

is output from the

speakers connected

with this unit.

•The HDMI audio signals selected for ZONE2 are only output to the

HDMI ZONE2 OUT connector. (The HDMI audio signals selected

for ZONE2 are not output from the speaker of the TV in ZONE2

that is connected to this unit.)

–

GHDRadioH

Symptom Cause/Solution Page

Reception fails, or

there is a lot of noise

or distortion.

•Change the antenna orientation or position.

•Separate the AM loop antenna from the unit.

•Use an FM outdoor antenna.

•Separate the antenna from other connection cables.

Basic version

Advanced version

InformationsInformations

DVD

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon AVR-3313CI Seite 176

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Denon AVR-3313CI

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info