498659
32
Zoom out
Zoom in
Vorherige Seite
1/125
Nächste Seite

Getting Started Connections Playback Remote ControlMulti-zone Information Troubleshooting Specifications
ENGLISH
Make the Optimal Speaker Settings, and Correct the Room Acoustics (Audyssey Auto Setup)
Do not remove the setup microphone until Audyssey Auto Setup is
completed.
When using headphones, unplug the headphones before starting
the Audyssey Auto Setup procedure.
1
Check the speaker connections.
(vpage 13 “Speaker Connections”)
2
Turn on the TV and subwoofer power.
Change the TV input to AVR-4310 input.
3
Turn on the AVR-4310 power.
(vpage 23 “Turning the Power On”)
4
Connect the setup microphone to the SETUP MIC
jack of the AVR-4310.
The “Audyssey Auto
Setup” screen is displayed
when you connect the
setup microphone.
Sound
receptor
a Connect the Included Setup
Microphone
NOTE
Loud test sounds may be played during Audyssey MultEQ XT
automatic speaker setup. This is part of normal operation. If there
is background noise in room, these test signals will increase in
volume.
Do not stand between the speakers and setup microphone or allow
obstacles in the path while the measurements are being made. This
will cause inaccurate readings.
Make the room as quiet as possible. Background noise can disrupt
the room measurements. Close windows, silence cell phones,
televisions, radios, air conditioners, fluorescent lights, home
appliances, light dimmers, or other devices as measurements may
be affected by these sounds.
Cell phones should be placed away from all audio electronics during
the measurement process as Radio Frequency Interference (RFI)
may cause measurement disruptions (even if the cell phone is not
in use).
Operating MASTER VOLUME during the measurements will cancel
the measurements.
NOTE
Do not hold the microphone in your hand during measurements.
Avoid placing the microphone close to a seat back or wall as sound
reflections may give inaccurate results.
If you subwoofer provides volume and crossover settings, set these
as shown below before starting the Audyssey Auto Setup.
Volume setting : “12 o’clock” position” or the middle of the gain
knob’s range.
Low Pass Filter setting : Low Pass Filter Setting to “Off”, or
“Maximum/Highest Frequency”.
Phase setting : 0°
Standby mode setting : “Off”
5
Mount the setup microphone on a tripod or stand
and place it in the main listening position.
When placing the setup microphone, adjust the height of the
sound receiver part to the level of the listener’s ear.
Setup
microphone
Settings
32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Denon AVR-4310 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Denon AVR-4310

Denon AVR-4310 Bedienungsanleitung - Deutsch - 125 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info