498659
94
Zoom out
Zoom in
Vorherige Seite
1/125
Nächste Seite
0
Getting Started Connections Settings Playback Multi-zone Information Troubleshooting Specifications
ENGLISH
Operating the Main Remote Control Unit
[MUTE]
[ iPod]
[ NET/USB]
[0 ~ 9]
[POWER ON]
[DEVICE
SELECTOR]
[POWER OFF]
[RC SETUP]
[MASTER
VOLUME]
[SOURCE
SELECT]
[ MAIN]
[ TUNER]
When using multiple DENON AV receivers in the same room, make
this setting so that only the desired AV receiver operates.
Setting the Remote ID
NOTE
When changing a setting, be sure to set the same remote ID as the
AVR-4310’s (vpage 43).
When changing the MAIN mode’s remote ID, also change the
“TUNER”, “iPod”, and “NET/USB” remote ID at the same time.
DEVICE SELECTOR
Remote ID
MAIN TUNER iPod NET/USB
1
(Default)
81001 62863 72815 62865
2 82001 62275 72816 62837
3 83001 62276 72817 62838
4 84001 62277 72818 62839
1
Press [MAIN] to light the “MAIN” zone indicator.
2
Press and hold in [RC SETUP] for at least 3 seconds.
The signal transmission indicator flashes twice.
3
Refer to the table at the right, and use [0 ~ 9] to input
the 5-digit number corresponding to the remote ID
to be changed.
The signal transmission indicator flashes twice.
4
Press [TUNER], [iPod] or [NET/USB] to select the
mode to be set.
5
Repeat steps 2 to 4 to set the remote IDs for all
modes.
Signal
transmission
indicator
[0 ~ 9]
[DEVICE
SELECTOR]
[MACRO]
[RC SETUP]
Signal
transmission
indicator
If your AV devices are of a brand other than DENON or if they cannot
be operated with the preset memory function, their remote control
signals can be transfered to stored in the AVR-4310’s main remote
control unit.
Learning Function
1
Press and hold in [RC SETUP] for at least 3 seconds.
The signal transmission indicator flashes twice.
2
Press [9], [7] and [5], in that order.
The signal transmission indicator flashes twice and the learning
mode is set.
3
Press [DEVICE SELECTOR] for the device you want
to set
4
Press the button to be set.
The main remote control unit’s display turns off.
If a button that cannot be learned is pressed, the signal transmission
indicator lights but the signal is not learned.
b
5
Point the main remote control units directly at each
other and press and hold the button on the other
device’s remote control unit that you want to learn.
Once learning is completed normally, the display lights and the
signal transmission indicator flashes twice.
If you want to learn other buttons, repeat steps 4 and 5.
The mode can be switched by pressing [DEVICE SELECTOR].
The signal transmission indicator lights once for a long time if
learning was not possible
b
b
b
6
Press and hold in [RC SETUP] for at least 3 seconds.
The signal transmission indicator flashes twice and the setting
is completed.
[0 ~ 9]
[CHANNEL +, –]
[ DVD/HDP]
[ SAT/CBL]
[ VCR/DVR]
[ TV]
[DEVICE
SELECTOR]
[8], [1],
[9], [6],
[3], [7], [2]
[RC SETUP]
[ MAIN]
Signal
transmission
indicator
Remote Control
94

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Denon AVR-4310 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Denon AVR-4310

Denon AVR-4310 Bedienungsanleitung - Deutsch - 125 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info