Bedienungsanleitung Denon AVR-4800 (Seite 26 von 69) (Englisch)

584373

Zoom out

Zoom in

Vorherige Seite

1/69

Nächste Seite

Select “Yes”.

a. If the “Auto” mode is selected:

Test tones are automatically emitted from the different speakers.

The test tones are emitted from the different speakers in the

following order, at 4-second intervals the first time and second time

around, 2-second intervals the third time around and on:

Use the CURSOR buttons to adjust all the speakers to the same

volume.

The volume can be adjusted between –12 dB and +12 dB in units of

1 dB.

b. When the “Manual” mode is selected

Use the and cursor buttons to select the speaker from which

you want to produce the test tone, then use the and cursor

buttons to adjust so that the volume from the different speakers

sounds the same.

After the above settings are completed, press the ENTER button again.

The “Channel Level” screen reappears.

ENTER

Example: When the volume is set to –12 dB

while the test tone is being

produced from the subwoofer

Example: When the volume is set to –12 dB

while the subwoofer is selected

To cancel the settings, select “Level Clear” and “Yes” on the “Channel Level” screen, then make the settings again.

The level of each channel should be adjusted to 75 dB (C-weighted, slow meter mode) on a sound level meter at the listening position.

If a sound level meter is not available adjust the channels by ear so the sound levels are the same. Because adjusting the subwoofer level test

tone by ear is difficult, use a well known music selection and adjust for natural balance.

NOTE: When adjusting the level of an active subwoofer system, you may also need to adjust the subwoofer’s own volume control.

When you adjust the channel levels while in the SYSTEM SETUP CHANNEL LEVEL mode, the channel level adjustments made will affect

ALL surround modes. Consider this mode a Master Channel Level adjustment mode.

After you have completed the SYSTEM SETUP CHANNEL LEVEL adjustments, you can then activate the individual surround modes and

adjust channel levels that will be remembered for each of those modes. Then, whenever you activate a particular surround sound mode,

your preferred channel level adjustments for just that mode will be recalled. Check the instructions for adjusting channel levels within each

surround mode on Page 46.

You can adjust the channel levels for each of the following surround modes: DIRECT, STEREO, 5CH/7CH STEREO, DOLBY/DTS SURROUND,

HOME THX CINEMA, WIDE SCREEN, SUPER STADIUM, ROCK ARENA, JAZZ CLUB, CLASSIC CONCERT, MONO MOVIE, and MATRIX.

When using either surround speakers A or B, or when using surround speakers A and B at the same time, be sure to adjust the balance of

playback levels between each channel for the various selections of “A or B” and “A and B”.

Flashing

FL C FR SR SBR SBL SL SW

1spkr

2spkrs

When the surround back speaker setting is set to “1spkr” for

“Speaker Configuration”, this is set to “SB”.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon AVR-4800 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info