Bedienungsanleitung Denon AVR-4810CI (Seite 19 von 145) (Englisch)

584377

Zoom out

Zoom in

Vorherige Seite

1/145

Nächste Seite



Getting Started Connections Settings Playback Remote ControlMulti-zone Information Troubleshooting SpeciﬁcationsConnections

'- '3

."*/;0/&

;0/&;0/&

- 3

Speaker Connections

NOTE

Connect so that the speaker cable core wires do not protrude from

the speaker terminal. The protection circuit may be activated if the

core wires touch the rear panel or if the + and – sides touch each

other (v“Protection Circuit”).

Never touch the speaker terminals while the power supply is

connected. Doing so could result in electric shock.

•

When using a banana plug

Tighten the speaker terminal ﬁrmly before

inserting the banana plug.

Peel off about 0.03 ft/10 mm of sheathing

from the tip of the speaker cable, then

either twist the core wire tightly or

terminate it.

Turn the speaker terminal

counterclockwise to loosen it.

Insert the speaker cable’s core wire to

the hilt into the speaker terminal.

Protection Circuit

If the core wires touch the rear panel and the screws etc., or the ±

sides touch each other, the protection circuit will be activated and the

power indicator will ﬂash red at intervals of 0.5 secs.

If the protection circuit is activated, the speaker output is isolated, and

the power supply goes to the standby state. If the power supply is

turned off, after the power supply cord is withdrawn, please conﬁrm

that speaker cable and input cable are connected.

Also, if replaying large sound levels by using a speaker having an

impedance less than that speciﬁed (eg, 4 Ω/ohms), the temperature

will rise, and the protection circuit might be activated. The power

supply will go into the standby state, and the power indicator will ﬂash

red at 2 second intervals.

In this case, please switch off the power supply, and wait until the

AVR-4810CI has cooled down, and the surrounding ventilation is

good.

Even if there are no problems with the surrounding ventilation and

connections, in the event of the protection circuit becoming activated,

due to thinking that the AVR-4810CI has failed, please contact DENON

Service center after switching off.

Connecting the Speaker Cables

Carefully check the left (L) and right (R) channels and + (red) and – (black) polarities on the speakers being connected to the AVR-4810CI, and

be sure to interconnect the channels and polarities correctly.

NOTE

Connect so that the speaker cable core wires do not protrude from

the speaker terminal. The protection circuit may be activated if the

core wires touch the rear panel or if the + and – sides touch each

other (v“Protection Circuit”).

Never touch the speaker terminals while the power supply is

connected. Doing so could result in electric shock.

•

Use speakers where one speaker has an impedance of 6 ~ 16 Ω/

ohms. When using a speaker with impedance of 6 Ω/ohms to 8 Ω/

ohms, make sure to set the “Speaker Impedance” in the GUI menu

to “6 Ω/ohms”.

When using a banana plug

Tighten the speaker terminal ﬁrmly before

inserting the banana plug.

When the “Assign Mode” is set to “ALL Z2” or “ALL Z3”, only multi-zone audio is output from the AVR-4810CI speaker terminals.

For output in the MAIN ZONE, connect the output from the AVR-4810CI pre-out terminal to the power amp in the other room.

Turn the speaker terminal clockwise to

tighten it.

AVR-4810CI

Power ampliﬁer

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon AVR-4810CI Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info