Bedienungsanleitung Denon AVR-4810CI (Seite 102 von 145) (Englisch)

584377

102

Zoom out

Zoom in

Vorherige Seite

1/145

Nächste Seite



Getting Started Connections Settings Playback Remote ControlMulti-zone Information Troubleshooting SpeciﬁcationsPlayback

To cancel, press <ZONE2/3/4 / REC SELECT>, then turn <SOURCE

SELECT> until “ZONE2 SOURCE” is displayed.

Make a test recording before starting the actual recording.

Signals are only output to the analog REC OUT connectors when

the digital signals input to the digital input connectors (OPTICAL/

COAXIAL) are PCM (2-channel) signals.

As the digital audio signal input from the HDMI connector is not

output to the digital recording connector (OPTICAL), you should

connect using the OPTICAL and COAXIAL connectors.

Sources selected with the REC OUT mode are output from ZONE2

as well.

In the REC OUT mode, the remote control unit’s ZONE2 mode

buttons cannot be operated.

The “XM” and “HD Radio” digital audio output signals are not

output from the OPTICAL2 output connectors. Also, network audio

signals (Internet radio, music server, USB, Napster and Rhapsody)

are output as copy-protected signals.

•

NOTE

Recordings you make are for your personal enjoyment and should

not be used for other purposes without permission of the copyright

holder.

Input sources for which “Delete” is selected at “Source Delete”

(vpage 53) cannot be selected.

•

When you make an HDMI connection with a TV or player compatible

with AVR-4810CI and HDMI control functions, you can perform the

following operations by setting the HDMI control function of each

device.

When you want to listen to TV audio by AVR-4810CI, connect optical

digital or analog audio (vpage 21 “TV“).

When using these functions set as follows: “HDMI Control” –

“Control” (vpage 44) set to “ON“.

•

NOTE

When “Control” is set to “ON”, it consumes more standby power.

The HDMI control function controls operations of a TV that is

compatible with the HDMI control function. Make sure that the TV

and HDMI are connected when you perform HDMI control.

When you power off AVR-4810CI, the HDMI control function does

not operate. Either power on or set to standby.

Some functions may not operate depending on the connected TV

or player. Check the owner’s manual of each device for details

beforehand. Please refer to the DENON website for information on

compatible equipment.

When “Control” is set to “ON”, it is not possible to assign an HDMI

terminal to “TV” at “Input Assign” (vpage 59).

•

Turn the power on for all the equipment connected

by HDMI cable.

Set the HDMI control function for all equipment

connected by HDMI cable.

Set “HDMI Control” – “Control” (vpage 44) to “ON“.

Please consult the operating instructions for the connected

equipment to check the settings.

Carryout steps 1 and 2 should any of the equipment be plugged

out.

Switch the television input to the HDMI connected to

the AVR-4810CI.

Switch the AVR-4810CI input to the HDMI input

source and check if the picture from the player is ok.

When you turn the TV’s power to standby, check

that the power of the AVR-4810CI and player also

goes on standby.

If the HDMI control function does not operate properly, check the

following points.

Is the TV or player compatible with the HDMI control function?

Is the AVR-4810CI properly set?

Is the “HDMI Control” – “Control” (vpage 44) set to “ON”?

Is the “Power Off Control” (vpage 44) set to “ON”?

Is the “Control Monitor” (vpage 44) set for the monitor output

connected to television?

In the case of dual monitor connection, is the “Control Monitor”

(page 44) on the GUI menu set to a monitor without HDMI

control?

Are the HDMI control function settings of all equipment correct?

•

NOTE

Should any of the operations below be performed, the interlocking

function may be reset, in which case, repeat step’s 1 and 2.

“Input Assign” – “HDMI” (vpage 59) setting has changed.

“Monitor Out” (vpage 43) setting is changed.

There is a change to the connection between the equipment and the

HDMI, or an increase in equipment.

•

AVR-4810CI power off can be linked to the TV power

off step.

When you set “Output audio from amp” in the TV audio output

setup operation, you can switch the amp power on.

You can switch audio output devices with a TV

operation.

You can adjust AVR-4810CI volume in the TV volume

adjustment operation.

You can switch AVR-4810CI input source through

linkage to TV input switching.

When playing the player, the AVR-4810CI input

function switches to the function of that player.

HDMI Control Function

Convenient Functions

Other Operations

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon AVR-4810CI Seite 102

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info