Bedienungsanleitung Denon AVR-5800 (Seite 35 von 67) (Englisch)

584383

Zoom out

Zoom in

Vorherige Seite

1/67

Nächste Seite

Adjust as desired with the CONTROL

knob.

• To increase the bass or treble:

Turn the control clockwise. (The bass

or treble sound can be increased to

up to +12 dB in steps of 2 dB.)

• To decrease the bass or treble:

Turn the control counter clockwise. (The bass or treble

sound can be decreased to up to –12 dB in steps of 2 dB.)

If you do not want the bass and treble to be

adjusted, turn on the tone defeat mode.

The signals do not pass through the bass

and treble adjustment circuits, providing

higher quality sound.

TONE

DEFEAT

[2] Listening over headphones

Plug the headphones’ plug into the jack.

Connect the headphones to the PHONES jack.

The pre-out output (including the speaker output) is automatically

turned off when headphones are connected.

NOTE:

To prevent hearing loss, do not raise the volume level excessively

when using headphones.

(Main unit)

[3] Turning the sound off temporarily (muting)

Use this to turn off the audio output

temporarily.

Press the MUTE button.

Cancelling MUTING mode.

Press the MUTE button again.

(Remote control unit)

[4]

Combining the currently playing sound with the desired image

Simulcast playback

Use this switch to monitor a video

source other than the audio source.

Press the remote control unit’s VIDEO

SELECT button until the desired image

appears.

Cancelling simulcast playback.

• Select “SOURCE” using the video select button.

• Switch the program source to the component connected to

the video input.

(Remote control unit)

[5] Checking the currently playing program source, etc.

On screen display

• Each time an operation is performed, a

description of that operation appears

on the display connected to the unit’s

VIDEO MONITOR OUT jack. Also, the

unit’s operating status can be checked

during playback by pressing the remote

control unit’s ON SCREEN button.

Such information as the position of the

input selector and the surround

parameter settings is output in

sequence.

Front panel display

• Descriptions of the unit’s operations

are also displayed on the front panel

display. In addition, the display can be

switched to check the unit’s operating

status while playing a source by

pressing the STATUS button.

STATUS

(Main unit)

Using the dimmer function

• Use this to change the brightness of the

display.

The display brightness changes in four steps

(bright, medium, dim and off) by pressing the

remote control unit’s DIMMER button

repeatedly.

The brightness changes in 3 steps each time

the button is pressed, and finally the display

turns off.

[6] Switching the surround speakers

The surround speakers switch as

shown below each time the SPEAKER

button is pressed.

SURROUND A SURROUND B

SURROUND A+B

This operation is possible when the setting for using both

surround speakers A and B is made at “Speaker

Configuration” in the System Setup Menu.

(Remote control unit)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon AVR-5800 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info